ISIS Power

Visit our community sponsor

  • Roadster Recent Posts

    edwardb

    Therma Barrier

    This is discussed in dozens (literally) of threads. Here are a few. More links inside these. Even more on the other forum since it's been around longer.

    edwardb Today, 10:28 AM Go to last post
    BEAR-AvHistory

    Therma Barrier

    I used ThermoTec, a bit pricey, (Summit, JEGS, Amazon) on all the heat facing sides of the boxes, firewall & inside of the trans tunnel. Live in

    BEAR-AvHistory Today, 10:26 AM Go to last post
    R Thomas

    Race Setup changes on my Electric

    Wow, this is awesome and interesting development of kit. Congrats and best of luck on getting that record.

    R Thomas Today, 10:26 AM Go to last post
    Walt

    Sun shade

    Seems like I remember somebody in Arizona used to make and sell sun shades for roadsters, does any one know if they are still doing them?

    Walt Today, 10:01 AM Go to last post
    jwebb

    Therma Barrier

    Looking for suggestions/recommendations on thermal barrier for foot boxes, floor boards, etc., ideas?

    jwebb Today, 09:25 AM Go to last post
    jmccabe

    Race Setup changes on my Electric

    Ok, weekend went great !
    Car changes all worked as designed. The only change made was to increase the rear spoiler angle its highest angle (72

    jmccabe Today, 09:18 AM Go to last post
    GoDadGo

    TKO 600 final drive gear

    That's How They Roll Where I Live!

    85-90 MPH is the average commuting cruising speed with triple digit speeds not that uncommon on the Twin

    GoDadGo Today, 09:17 AM Go to last post
    boBQuincy

    2nd wheel mounting problem today

    Tungsten weights for pinewood derby cars are about twice as dense as lead, about 1/16" thick.

    boBQuincy Today, 08:51 AM Go to last post
    NAZ

    2nd wheel mounting problem today

    Larger wheels / smaller brakes are the obvious fix or even different calipers with the same rotors. These are costly options so it's understandable you're

    NAZ Today, 07:58 AM Go to last post
    DaveS53

    TKO 600 final drive gear

    65 mph is not cruising speed where I live. I drove 360 highway miles from Loveland to Pueblo and back this weekend, going 80 mph whenever possible.

    DaveS53 Today, 07:52 AM Go to last post
    rich grsc

    2nd wheel mounting problem today

    Where on the caliper is it hitting? You may be able to clearance the caliper by hitting it with a grinder.

    rich grsc Today, 07:35 AM Go to last post
    CraigS

    Wheels and tires for the track

    335s are tough. I have given up on them. Really they need minimum 11 in wheel and 12 would be best. Unfortunately once you go beyond 10.5x17 they get

    CraigS Today, 07:11 AM Go to last post
    walt mckenna

    TKO 600 final drive gear

    My 4.6 does not have the torque of a Coyote, but I see the same benefits with the .64 and 3:55 combination as Mr King. Mine also sees track time and I

    walt mckenna Today, 06:58 AM Go to last post
    CraigS

    2nd wheel mounting problem today

    Yes, 2 possibilities. 1-While it's not as sophisticated a balancing process you can just static balance which, instead of inner and outer weights, puts

    CraigS Today, 06:52 AM Go to last post
    j.miller

    Srobinsonx2 Bodywork

    No need to spot in with SS, go to the Shop Line 2K. spray with a 1.7- 1.8 cap....I mix 4,1,1.5 and wait a little longer between coats ( till you see the

    j.miller Today, 06:26 AM Go to last post
    wareaglescott

    TKO 600 final drive gear

    .64 for me as well with a Coyote and 3.55 rear end. Same comments on drivability as King mentioned. Very pleased with it.

    wareaglescott Today, 05:47 AM Go to last post
    Jeff Kleiner

    Srobinsonx2 Bodywork

    You can spot in SS but if you are going to lay sealer over everything and are satisfied with the shape of the burn through area it is not necessary.

    Jeff Kleiner Today, 05:44 AM Go to last post
    2bking

    TKO 600 final drive gear

    I have a Coyote, 3.55 rear gears, TKO 600, and started out with the .82 fifth but after some freeway driving I decided to install the .64 ratio. I like

    2bking Today, 02:42 AM Go to last post
    GoDadGo

    TKO 600 final drive gear

    Does anybody have any experience with the Richmond 5-Speeds?
    Their final drive splits the difference at .77 Overdrive.

    https://www.summitracing.com/search/...ibanner=SREPD5

    GoDadGo Today, 02:14 AM Go to last post
    Bobby Doug

    TKO 600 final drive gear

    .64 X2, 3.31 rear axle. I guess it depends on where you live. Here in KS even our two lane roads are 65-70 mph and our interstates are 75 mph. So the

    Bobby Doug Today, 01:25 AM Go to last post

Racing Adventures

Visit our community sponsor