Boig Motorsports

Visit our community sponsor

Tab Content
  • jlfernan's Avatar
    Today, 03:27 PM
    Hey Mike thanks for the response. How about the red one? I was just thinking about removing the hard fuel line and replacing it with a braided hose....
    3 replies | 28 view(s)
  • jlfernan's Avatar
    Today, 03:06 PM
    I have an Edelbrock 7521 intake manifold like the one in the photo. I've already put my water temp switch in the port behind the water neck. My water...
    3 replies | 28 view(s)
  • jlfernan's Avatar
    07-20-2017, 05:59 AM
    jlfernan replied to a thread Wheels hit rear caliper in Roadster
    I ended up using a 1/8" spacer and that resolved the problem. These wheels are made by Team III and if I understand basckspacing, the FFR wheels have...
    14 replies | 601 view(s)
  • jlfernan's Avatar
    07-17-2017, 04:45 PM
    I just received my Hydroboost from Forte. Banjo fittings with AN ends are used on the master cylinder. To connect my hardlines to the banjos I needed...
    8 replies | 560 view(s)
  • jlfernan's Avatar
    07-16-2017, 07:24 PM
    As delivered from FFR. One-3/4" and One-5/8". Includes 2 plastic angled inlet adapter with hose clamps and 2 90 brake line adapters. Reservoir hose...
    1 replies | 122 view(s)
  • jlfernan's Avatar
    07-16-2017, 01:42 PM
    FYI I mocked it up inside the DS footbox. I bought 1/8" aluminum angle. I drilled through the angle at 3/8" which puts the bolt head(mine came with...
    11 replies | 521 view(s)
  • jlfernan's Avatar
    07-16-2017, 05:49 AM
    I was trying to work out where to drill for the rod bearings so that the bellcrank inside the footbox won't hit the top and it was giving me a...
    11 replies | 521 view(s)
  • jlfernan's Avatar
    07-14-2017, 06:18 PM
    jlfernan replied to a thread Hydroboost problem. in Roadster
    I just went and ground off the bit that was interfering. A new question I have is what fittings do I need to make the brake work with the banjo...
    2 replies | 169 view(s)
  • jlfernan's Avatar
    07-14-2017, 03:14 PM
    jlfernan started a thread Hydroboost problem. in Roadster
    I just got my hydroboost from Mike Forte. Mine interferes with the flanges that hold the steering shaft bearings. Did anybody out there have to trim...
    2 replies | 169 view(s)
  • jlfernan's Avatar
    07-10-2017, 11:43 AM
    Car's looking great. Three question 1-Did Mike send you instructions for the mechanical throttle?, 2-What measurement did you use for the rod end...
    73 replies | 22089 view(s)
  • jlfernan's Avatar
    07-09-2017, 04:54 PM
    jlfernan replied to a thread Wheels hit rear caliper in Roadster
    Yea, I think that's the route I'm taking. I've already ordered a set. We think there's too much backspacing on these wheels which is allowing the...
    14 replies | 601 view(s)
  • jlfernan's Avatar
    07-09-2017, 08:48 AM
    jlfernan replied to a thread Wheels hit rear caliper in Roadster
    The problem as I see it is that the distance from the outside edge of the disc, the brake pad and caliper are fixed. there is no way to adjust that...
    14 replies | 601 view(s)
  • jlfernan's Avatar
    07-08-2017, 08:52 PM
    jlfernan replied to a thread Wheels hit rear caliper in Roadster
    Their website says 6 5/8". I hate when some are fractions, others decimal. For the heck of it I put some 1/16" washers on three of the wheel studs....
    14 replies | 601 view(s)
  • jlfernan's Avatar
    07-08-2017, 08:23 PM
    Like the title says. Have some ET Wheels Halibrand replicas. 17X10.5. Had the tires mounted today and tried them on the car to see how they look and...
    14 replies | 601 view(s)
  • jlfernan's Avatar
    07-08-2017, 05:23 PM
    Looking through my engine parts and came across the cheesy coolant plastic filler neck. On my first car, FFR supplied a nice aluminum one. If any one...
    4 replies | 159 view(s)
  • jlfernan's Avatar
    06-28-2017, 02:51 PM
    Speed Shifting = Shifting just as fast as you would power shifting, using the clutch, but only lifting about half way off the gas.
    20 replies | 895 view(s)
No More Results

2 Visitor Messages

  1. View Conversation
    jorge,
    are you still selling fender spats? If so, do you have black or just clear? Also, how do I order a pair? Thanks.
    Rick
Showing Visitor Messages 1 to 2 of 2
About jlfernan

Basic Information

About jlfernan
Location:
Hialeah, Fl
Interests:
Flying, cars
Occupation:
Police Officer

Signature


Statistics


Total Posts
Total Posts
239
Posts Per Day
0.10
Visitor Messages
Total Messages
2
Most Recent Message
03-30-2014 05:30 PM
General Information
Last Activity
Today 04:54 PM
Join Date
02-12-2011
Referrals
1
View jlfernan's Blog

Recent Entries

Clear fender spats

by jlfernan on 04-12-2011 at 04:59 PM
Quote Originally Posted by jlfernan View Post
OK guys, got more material and ready to ship. For those of your that already PM'ed me, they're in route. Anyone else interested just shoot me a PM and I'll get you taken care of.
Categories
Uncategorized

Replica Parts

Visit our community sponsor