FormaCars

Visit our community sponsor

Tab Content
  • j.miller's Avatar
    11-17-2017, 07:26 AM
    Just noticed you have a cheater valve on the gun (not a fan) You will need to open it all the way and then adjust your pressure regulator at the...
    762 replies | 245111 view(s)
  • j.miller's Avatar
    11-14-2017, 08:28 AM
    j.miller replied to a thread #8952 Graduation in Roadster
    Well done brother. If I make it to the Texas Cobra Club bash I hope to see you !...da bat
    28 replies | 613 view(s)
  • j.miller's Avatar
    11-08-2017, 07:23 PM
    951-676-0191 (double secret bat phone)....da Bat.....His self !......well, it WAS double secret! damn it !
    5 replies | 244 view(s)
  • j.miller's Avatar
    11-08-2017, 08:39 AM
    j.miller replied to a thread Brake lines in Roadster
    It works out between 4.837 to 5.276 /. So 5% is a fair guestimate.....Then there is the "Feels Like" factor to take into account...
    22 replies | 855 view(s)
  • j.miller's Avatar
    11-07-2017, 08:41 AM
    j.miller replied to a thread Hood Fit Tricks? in Roadster
    Most of the time we are trying to pull the corners down...yours is reverse.... I have seen this 5-6 times. I used rubber blocks on top of the tubing...
    6 replies | 340 view(s)
  • j.miller's Avatar
    11-06-2017, 07:16 PM
    j.miller replied to a thread Respirator Advice in Roadster
    The filter on the end of my cigarette does the trick for me....that , and I can hold my breath for three and a half mins....but that's me. Particle...
    10 replies | 311 view(s)
  • j.miller's Avatar
    11-04-2017, 08:29 AM
    frankb.....You say "If you have a nostalgic connection to the Cleveland"....WHAT THE HELL IS THAT !!! There was a time in my life when you say "351...
    7 replies | 432 view(s)
  • j.miller's Avatar
    11-04-2017, 08:16 AM
    j.miller replied to a thread Engine Compartment Size in Roadster
    Like David just stateted, it can be tricky with the Air Gap. The other problem we have seen with the taller intakes is you have to run a smaller air...
    5 replies | 314 view(s)
  • j.miller's Avatar
    11-04-2017, 08:08 AM
    289 is a complete kit with radiator , no doner option
    21 replies | 796 view(s)
  • j.miller's Avatar
    11-02-2017, 08:33 PM
    It's not a mistake, doesn't need to be square. It is the way it is because it is designed to use a 5.0 radiator. A lot of little things lead back to...
    21 replies | 796 view(s)
  • j.miller's Avatar
    10-26-2017, 07:18 AM
    j.miller replied to a thread Exhaust Cut Outs in Roadster
    A little bit of difference at the motor makes a lot a bit of difference at the body....a lot!
    5 replies | 308 view(s)
  • j.miller's Avatar
    10-25-2017, 06:41 PM
    j.miller replied to a thread Exhaust Cut Outs in Roadster
    They are for J-pipes....so if that's what you are using they are close. If you are going 4 into 4's just leave them alone for now....typically , with...
    5 replies | 308 view(s)
  • j.miller's Avatar
    10-25-2017, 06:21 AM
    j.miller replied to a thread Hood Scoop in Roadster
    Jim1885 ,Shell Valley had a couple of scoops. You might give them a look
    20 replies | 1390 view(s)
  • j.miller's Avatar
    10-24-2017, 06:57 AM
    You could do a single stage with a flattening agent. When it's dry (a week) you can actually polish the sides to give them a little more shine and...
    12 replies | 591 view(s)
No More Results
About j.miller

Basic Information

Statistics


Total Posts
Total Posts
388
Posts Per Day
0.16
General Information
Last Activity
Yesterday 07:25 PM
Join Date
02-25-2011
Referrals
0

2 Friends

  1. Cfehrenb Cfehrenb is offline


    Cobrapreneur

    Cfehrenb
  2. howling-cobra howling-cobra is offline

    Junior Member

    howling-cobra
Showing Friends 1 to 2 of 2

Vintage Wheels

Visit our community sponsor