Very Cool Parts

Visit our community sponsor

Tab Content
  • Jacob's Avatar
    05-23-2017, 04:01 PM
    Jacob started a thread Wiper Motor Wiring ? in Roadster
    Does anyone sell a male plug-in that will match up to the female plug-in on the wiper motor? Seems like it would make a neater more fail safe way of...
    6 replies | 316 view(s)
  • Jacob's Avatar
    05-20-2017, 08:06 AM
    Jacob replied to a thread Srobinsonx2 Bodywork in Roadster
    Where does one find Rosin Paper typically or does it have another common name?
    63 replies | 3246 view(s)
  • Jacob's Avatar
    05-19-2017, 04:49 PM
    Jacob replied to a thread Heater Box outlets? in Roadster
    thanks I assumed so
    6 replies | 272 view(s)
  • Jacob's Avatar
    05-19-2017, 04:32 PM
    Jacob started a thread Heater Box outlets? in Roadster
    The heater box has four air outlets, 2 are round and 2 are oval shaped...does it matter which two are used for the heater tubing and which two are...
    6 replies | 272 view(s)
  • Jacob's Avatar
    05-18-2017, 07:59 PM
    Dash / Gauge / Switch wiring roughed in and tested most of the circuits and so far they all work as designed...even the Russ Thompson dimmer / flash...
    46 replies | 5965 view(s)
  • Jacob's Avatar
    05-14-2017, 08:04 PM
    Not sure what you used, but regular contact cement (DAP brand) should work real well.
    13 replies | 495 view(s)
  • Jacob's Avatar
    05-10-2017, 08:32 PM
    Here is a pic of the bracing I built for the grab bar. It's 1/2 inch x 1/8 inch flatbar with extra bracing welded on and its real firm. This view is...
    46 replies | 5965 view(s)
  • Jacob's Avatar
    05-10-2017, 08:26 PM
    Jacob replied to a thread Speedhut Fuel gauge?'s in Roadster
    Sorta thought the clock really isn't anywhere as necessary as an oil temp gauge anyway?
    13 replies | 568 view(s)
  • Jacob's Avatar
    05-10-2017, 04:18 PM
    Jacob replied to a thread Speedhut Fuel gauge?'s in Roadster
    I'll answer my own questions: Per Speedhut, they provide one program button and expect you to use it primarily on the speedo...then temporarily as...
    13 replies | 568 view(s)
  • Jacob's Avatar
    05-09-2017, 04:45 PM
    Any problems with how I mounted the inertia switch? Covered the dash with marine vinyl that has a nice pattern to it. First covered with vinyl...
    46 replies | 5965 view(s)
  • Jacob's Avatar
    05-09-2017, 04:14 PM
    Jacob started a thread Speedhut Fuel gauge?'s in Roadster
    I have two wires coming out of the fuel gauge: yellow / orange stripe and yellow / black stripe...the RF harness at the tank has a green gas sender...
    13 replies | 568 view(s)
  • Jacob's Avatar
    05-01-2017, 08:24 PM
    You've done a great job and I've been able to learn so much following your build...you should be proud of your accomplishment...its a shame your Dad...
    57 replies | 8861 view(s)
No More Results
About Jacob

Basic Information

About Jacob
Biography:
Since I was very young always enjoyed cars and working with them. Currently have a 37 Ford and 29 Ford, sold an 08 Corvette to finance a MKIV that should be delivered around the first of September. The information base of this forum is off the scale and invaluable, would hope at some time I can provide just a small piece of the valuable info that others provide.
Location:
Rogers, AR
Interests:
cars, guitars and grandkids
Occupation:
Retired Environmental Eng

Signature


MK IV complete Kit - 1st time builder started Sept 2016
Levy 306
T5
2015 Mustang IRS
Power steering - Levy setup, Breeze roll bars, Thompson trunk box
fuel injection, powder coating, sway bars, heater, wipers, 17 in wheels

Statistics


Total Posts
Total Posts
109
Posts Per Day
0.32
General Information
Last Activity
Today 03:24 PM
Join Date
06-21-2016
Referrals
0

Lodestone Billetworks

Visit our community sponsor