ReinCarNation

Visit our community sponsor

  • Roadster Recent Posts

    roadscholar

    Driver's footbox tight

    Jeff,

    I have size 14E feet. I did a couple of things. With the small block Ford, as you are using, I pushed the right side of the footbox

    roadscholar Today, 04:46 PM Go to last post
    Paparazzi

    Holley carb questions

    Great - thanks all!

    I'll bring the idle down to 14/15. I've no details on the engine at all other than it's a 351 roller, "Rebuilt

    Paparazzi Today, 03:32 PM Go to last post
    NAZ

    Holley carb questions

    You are interpreting the total advance correctly, base is 17, 38 total, all in by 3500. I'm with Mike, 38 total seems a bit too advanced but do you have

    NAZ Today, 02:55 PM Go to last post
    mike223

    Holley carb questions

    Looks good - I would drop the advance 3 degrees for 35 degrees total and keep an eye ear on it.

    mike223 Today, 02:39 PM Go to last post
    davekp

    Steering Ratio Help

    I have a 3 turn and I'd like it a bit slower, but none seems to be available.

    davekp Today, 02:19 PM Go to last post
    BadAsp427

    Holley carb questions

    Those number all look real good, but I believe that 14 should be your idle advance and that would bring your top (all in) advance to about 36... These

    BadAsp427 Today, 02:14 PM Go to last post
    Paparazzi

    Holley carb questions

    I'll put the choke back on at some point, probably.

    So, that done, now I'm back to the timing. :-)

    Just took some readings.

    Paparazzi Today, 01:53 PM Go to last post
    BEAR-AvHistory

    Driver's footbox tight

    Panel also bumped out by hand as Coyote was installed before FFR developed the Coyote install sheet metal.

    Second item is Puma driving

    BEAR-AvHistory Today, 01:47 PM Go to last post
    cobrajj

    Driver's footbox tight

    Bumped the panel as far to the right. riveted the panel to the square tunnel tubes, and made a filler piece to secure to the 4" tube.

    cobrajj Today, 01:38 PM Go to last post
    Saul S

    Warning! Built Not Bought

    Here is mine that I proudly display. Since it's a Factory Five registered trademark I even went so far as to get written permission from Mr Dave Smith.

    Saul S Today, 01:34 PM Go to last post
    Railroad

    Rear Wheel Track

    Thanks guys for replying and helping cure my problems. After Bad Asp offer, I went to the barn/shop to review, before calling him. I found the wheel

    Railroad Today, 01:28 PM Go to last post
    Railroad

    Holley carb questions

    That is great news. I look forward to reading you having the elec choke up and working like it should.
    I seem to remember, the elec source was

    Railroad Today, 01:17 PM Go to last post
    Murd

    Driver's footbox tight

    Jeff,
    I think the original mk4 panel had more foot room/less engine room. Probably ask for that one.
    Basically any shoe as narrow and thin

    Murd Today, 01:14 PM Go to last post
    Paparazzi

    Holley carb questions

    Update - hopefully final.

    So ... that 'electric choke' cable was bothering me. It wasn't 'tagged', it actually says it on the wire. So I

    Paparazzi Today, 01:05 PM Go to last post
    videodude

    How do I add my car info to my posts?

    Go to Settings (top right corner of the page), then on the left side of the next page go to Edit Signature and enter your car information or whatever

    videodude Today, 12:51 PM Go to last post
    Paparazzi

    Holley carb questions

    Just back from a quick trip. If the seat of the pants dyno is anything to go by, it's a big improvement. A bump on the throttle at 80 gives quite a nice

    Paparazzi Today, 12:37 PM Go to last post
    doddmoore

    Thermo-tec in engine compartment

    Thanks guys. I’m going to take them out and get them painted to match my F panels and reinstall. I do want to be as proud as possible. I want people

    doddmoore Today, 12:35 PM Go to last post
    Jeff's First FFR

    How do I add my car info to my posts?

    Hello all,
    It was suggested I add my car specifications to my posts. However, I am new at this and I can't find the place to do it.
    Thanks

    Jeff's First FFR Today, 12:06 PM Go to last post
    cv2065

    chevy engine

    Not that I would do it, but have to say that the Mercruiser dressed out like that looks tough.

    cv2065 Today, 11:48 AM Go to last post
    NAZ

    Holley carb questions

    If you have a wire from the 6AL labeled "electric choke" I suspect someone other than MSD placed that label on there. I've run your same CD

    NAZ Today, 11:47 AM Go to last post

Lodestone Billetworks

Visit our community sponsor