View Profile: EZ$ - Factory Five Forums

04-16-2019, 06:29 PM

EZ$ replied to a thread Is this normal??? in Roadster

For someone doing their first build ever, this can be some of the most frustrating, and rewarding experiences you'll ever have. One of the best tools...

33 replies | 1161 view(s)

04-16-2019, 06:22 PM

EZ$ replied to a thread Speedhut oil pressure sender connections in Roadster

After answering on the other forum, I just thought of a quick follow up question. The water temp., and oil temp. senders are only set up for one...

6 replies | 101 view(s)

04-16-2019, 02:49 PM

EZ$ started a thread Speedhut oil pressure sender connections in Roadster

OK, so I've read a bunch of threads regarding how to hook up the sender, but I'm still confused (big surprise)! I know Jeff Kleiner recommends using...

6 replies | 101 view(s)

04-15-2019, 10:20 PM

EZ$ replied to a thread Heater hose connection to water pump in Roadster

John, in addition to the hose I mentioned on the other forum, I looked at that 90 degree fitting. Once i start routing the hose, I may go back and...

7 replies | 234 view(s)

04-15-2019, 03:02 PM

EZ$ replied to a thread Heater hose connection to water pump in Roadster

Thanks Richard, Today I'm off to the local parts store. I think I've reached the point where if I need it, I'm going to buy it and to hell with any...

7 replies | 234 view(s)

04-14-2019, 09:47 PM

EZ$ replied to a thread Heater hose connection to water pump in Roadster

Thanks Frank. Wasn't sure that something like this was available. I'll check this out, and also with my local parts store. One of these days I hope...

7 replies | 234 view(s)

04-14-2019, 08:26 PM

EZ$ started a thread Heater hose connection to water pump in Roadster

Trying to get all my plumbing taken care of before I start the wiring. I ran into a problem hooking up the heater hose to the water pump fitting. The...

7 replies | 234 view(s)

04-09-2019, 09:11 PM

EZ$ replied to a thread Couple of driveline questions in Roadster

BadAsp, you might be on to something that I hadn't even considered. I didn't check to see if the hole/slot pattern in the A frame is offset to one...

9 replies | 371 view(s)

04-09-2019, 03:52 PM

EZ$ replied to a thread Couple of driveline questions in Roadster

David, I knew that the trans was going to be offset to the PS, just wasn't sure how much it should be. Since I'm doing an FIA the side pipe situation...

9 replies | 371 view(s)

04-08-2019, 10:53 PM

EZ$ replied to a thread Couple of driveline questions in Roadster

No offence taken. I'm just trying to figure this out. When Gordon sent the engine, they had put the motor mounts on, and although I removed them, I...

9 replies | 371 view(s)

04-08-2019, 01:27 PM

EZ$ replied to a thread Couple of driveline questions in Roadster

Kevin, it looks to be similar. I know that more is in the trans than out. Any idea about the alignment of everything in relation to the A frame?...

9 replies | 371 view(s)

04-08-2019, 12:29 PM

EZ$ replied to a thread Self inflicted issues in Roadster

Rich, thanks for the pictures. I had to really stare at them to see exactly the parts you mentioned, (my eyesight is so bad, even with my reading...

19 replies | 913 view(s)

04-08-2019, 12:19 PM

EZ$ replied to a thread Couple of driveline questions in Roadster

I was hoping that someone had an answer. Just don't want this to get totally lost, so a bump to the top.

9 replies | 371 view(s)

04-07-2019, 03:27 PM

EZ$ started a thread Couple of driveline questions in Roadster

OK, so I'm trying to get the trans mount buttoned up. I'm using an S10 tail shaft, and got the hybrid mount from Mike Fortes, and this is an IRS car....

9 replies | 371 view(s)

04-07-2019, 02:05 PM

EZ$ replied to a thread Self inflicted issues in Roadster

Bill, sounds like it would have made my life a bit simpler.

19 replies | 913 view(s)

04-06-2019, 03:57 PM

EZ$ replied to a thread Self inflicted issues in Roadster

Bill, I'm glad Rich jumped in here, cause I wasn't sure what you were talking about! I'm still not sure, but that just shows my lack of knowledge....

19 replies | 913 view(s)

04-04-2019, 10:58 PM

EZ$ replied to a thread Self inflicted issues in Roadster

Dwheeler, that's one of my options if the Breeze part won't work.

19 replies | 913 view(s)

04-03-2019, 08:08 PM

EZ$ replied to a thread Self inflicted issues in Roadster

Dave, That looks as if it would thread into the port where I currently only have my water temp gauge sender. I could connect the heater hose and the...

19 replies | 913 view(s)

04-03-2019, 06:42 PM

EZ$ replied to a thread Self inflicted issues in Roadster

OK, so there's the port just above the thermostat, but that one is holding the coolant temperature sensor for the Fuel injection system. The other...

19 replies | 913 view(s)

04-03-2019, 12:21 AM

EZ$ replied to a thread Self inflicted issues in Roadster

Will heat help or hinder the removal. I'll check out the torx bits and see if I can get it to bite without damaging the intake manifold. Just really...

19 replies | 913 view(s)

04-02-2019, 08:29 PM

EZ$ started a thread Self inflicted issues in Roadster

So, I was trying to finish the plumbing before I started with the engine compartment wiring, and I needed a port for a barbed hose fitting to connect...

19 replies | 913 view(s)

04-01-2019, 12:50 PM

EZ$ replied to a thread The view from my hotel this morning - Ala Wai Harbor - Honolulu in Off Topic Discussions

Pete, I was going to say either Lake Como, or Lake Lucerne?

19 replies | 709 view(s)

03-31-2019, 01:03 PM

EZ$ replied to a thread Happy 60th Birthday to Da Bat! in General Discussions

Sorry to show up late for the party. Hope you had a terrific birthday celebration. I'm looking forward to possibly getting my car to you for paint...

39 replies | 711 view(s)