Very Cool Parts

Visit our community sponsor

Tab Content
  • EZ$'s Avatar
    07-11-2019, 10:07 AM
    Thanks Dave, that's the answer I was kind of looking for. If the tee won't help the situation then I'll replace that top hose and fill as you and...
    24 replies | 583 view(s)
  • EZ$'s Avatar
    07-10-2019, 07:07 PM
    Dave, It sounds like putting a tee filler in the top hose could also be the answer, but I just wasn't sure if it would cause any issues that I'm not...
    24 replies | 583 view(s)
  • EZ$'s Avatar
    07-10-2019, 05:18 PM
    EZ$ replied to a thread Heat and Sound Barriers in Roadster
    Has anyone tried this product? Been looking at it for awhile, and it looks interesting. www.carinsulation.com/buycarinsulation.html
    28 replies | 1546 view(s)
  • EZ$'s Avatar
    07-10-2019, 02:24 PM
    Bump to top. Hopefully someone has an answer. Thanks
    24 replies | 583 view(s)
  • EZ$'s Avatar
    07-09-2019, 08:21 PM
    Got the lines switched around. The bottom line from the Harrison tank now goes to the return line from the heater, and into the water pump lower...
    24 replies | 583 view(s)
  • EZ$'s Avatar
    07-09-2019, 02:00 PM
    OK, so I double checked how I had this plumbed, and it turns out, you are correct. I had the Harrison tank plumbed to the inlet side of the heater!...
    24 replies | 583 view(s)
  • EZ$'s Avatar
    07-09-2019, 10:48 AM
    Rich, I'll double check which side it's plumbed to. I believe I checked with Mike Forte when I was running the lines.
    24 replies | 583 view(s)
  • EZ$'s Avatar
    07-08-2019, 11:20 PM
    Last question for this, at least for now. Is there any down side to adding an inline filler to the top hose? It's either that, or a half stick of...
    24 replies | 583 view(s)
  • EZ$'s Avatar
    07-08-2019, 01:19 PM
    Rich, the return for the heater, and the Harrison tank go to a fitting just behind the thermostat housing. The red line in the picture is the route...
    24 replies | 583 view(s)
  • EZ$'s Avatar
    07-08-2019, 12:38 PM
    OK, so the tank sits just a bit higher than the top of the radiator, but the heater sits higher than the tank. IMAG1292 by Rick Paul, on Flickr The...
    24 replies | 583 view(s)
  • EZ$'s Avatar
    07-07-2019, 11:34 AM
    Craig and Paul, thanks for the recommendations on the PS pump fill. I'll try to find a way to get a bit more fluid in before starting, and top it off...
    24 replies | 583 view(s)
  • EZ$'s Avatar
    07-06-2019, 10:51 PM
    Thanks Dave. Do you think the amount of fluid I'm starting with, about 12-14oz., is going to be enough to protect the pump motor until more can be...
    24 replies | 583 view(s)
  • EZ$'s Avatar
    07-06-2019, 06:20 PM
    I went with a base kit because I wanted to do an FIA car, and of course I was about a year early for FFR's FIA full kit. If I had it to do over...
    35 replies | 1156 view(s)
  • EZ$'s Avatar
    07-06-2019, 06:09 PM
    I know this must have been discussed before, but in searching, I cannot find anything regarding a system with a Harrison expansion tank. Since the...
    24 replies | 583 view(s)
  • EZ$'s Avatar
    07-05-2019, 11:40 AM
    EZ$ replied to a thread A Couple of Strange Questions in Roadster
    Boyd, I was wondering if was related to a different configuration in the rear suspension. I've got the T-Bird IRS, so maybe it was something I didn't...
    4 replies | 344 view(s)
  • EZ$'s Avatar
    07-04-2019, 03:13 PM
    Well one strange, and another not so much. Does anyone know what the opening that this cover fills in was for, or is for? For the life of me, I...
    4 replies | 344 view(s)
  • EZ$'s Avatar
    06-24-2019, 11:04 AM
    John, Just a note regarding the RT turn signal unit. You may already know that you can separate the hub from the shaft. I didn't, and it caused some...
    16 replies | 767 view(s)
No More Results
About EZ$

Basic Information

About EZ$
Biography:
Saw my first Cobra when I was 15. Have been wanting to own one ever since. Trying to finish my FFR. Using a "Mr. Bruce" 289FIA body.
Location:
San Ramon, CA

Signature


Rick

Mk4 with Mr. Bruce FIA body, Levy 331 w/ Speedmaster Stack Injection, IRS, ABS, PS, PB, FAST FI

Statistics


Total Posts
Total Posts
252
Posts Per Day
0.13
General Information
Last Activity
Yesterday 05:21 PM
Join Date
02-17-2014
Referrals
0
No results to show...

Lodestone Billetworks

Visit our community sponsor