BluePrint Engines

Visit our community sponsor

Tab Content
  • jamesfr58's Avatar
    06-22-2019, 10:09 PM
    Beeman, I was looking for fire suppression and ran across this one that was originally designed for RV but I think this could work in the get as...
    8 replies | 938 view(s)
  • jamesfr58's Avatar
    06-22-2019, 09:41 PM
    Got some smaller thing done, interior lights mounted under dash and fit the waterfall back on the tunnel after making the small belt pieces to cover...
    158 replies | 10253 view(s)
  • jamesfr58's Avatar
    06-17-2019, 12:28 PM
    Up to something new..... Can't wait to see what you come up with
    519 replies | 79789 view(s)
  • jamesfr58's Avatar
    06-17-2019, 12:23 PM
    On a off topic, I worked on the cover when it was raining, but when it would stop I designed a sub structure for the front end of the pontoon boat to...
    158 replies | 10253 view(s)
  • jamesfr58's Avatar
    06-17-2019, 12:06 PM
    Ok will I could not take the wrinkles in the cover piece for the accumulator so.... I tore it off and recovered it again but this time just used the...
    158 replies | 10253 view(s)
  • jamesfr58's Avatar
    06-17-2019, 12:03 PM
    jamesfr58 replied to a thread GTM Trans-Am? in GTM Supercar
    Way to go, impressive run coagulations are in order !!
    8 replies | 344 view(s)
  • jamesfr58's Avatar
    06-16-2019, 11:23 AM
    First let me say Happy Father Days to all the father out there, for taking the time to pass on their knowledge from building a car (learning mechanic...
    158 replies | 10253 view(s)
  • jamesfr58's Avatar
    06-16-2019, 12:13 AM
    I had a hard time trying to get the golf heat reflecting material to lay down right on the cover as I put a bead roll on the face to stiffen it and...
    158 replies | 10253 view(s)
  • jamesfr58's Avatar
    06-16-2019, 12:08 AM
    Finished the cover over the accumulator, have heat reflective material on one side and thermal mat on the other so should keep heat away for the...
    158 replies | 10253 view(s)
  • jamesfr58's Avatar
    06-14-2019, 11:35 PM
    I had the same issue where I had to use the bushing on the coolant system. I finally gave up as they never sealed all the way and would drip...
    7 replies | 245 view(s)
  • jamesfr58's Avatar
    06-14-2019, 11:21 PM
    Shoeless your boat is a little bigger than mine, but they both are fun anyway. Only have to get the anchor winch installed and it is all rigged out...
    158 replies | 10253 view(s)
  • jamesfr58's Avatar
    06-14-2019, 10:59 PM
    Here are the picture of the cover for the Accumulator installed, hit the post button to soon !!
    158 replies | 10253 view(s)
  • jamesfr58's Avatar
    06-14-2019, 10:57 PM
    Worked on building a piece to cover the hole where the Accumulator was relocated to in my build. I decided to finish closing off the fan section...
    158 replies | 10253 view(s)
  • jamesfr58's Avatar
    06-14-2019, 10:50 PM
    I made the pieces for the cupholder, they are sub-flooring plywood covered with African Rose Wood (Budinga Raw Wood veneer) and I ordered the lighted...
    158 replies | 10253 view(s)
  • jamesfr58's Avatar
    06-10-2019, 11:04 PM
    Nice clean installation looks good, mine is different routing to my G-96 tranny, I should take picture and post to see if it is ok where it is...
    205 replies | 22076 view(s)
  • jamesfr58's Avatar
    06-10-2019, 10:50 PM
    Looks like things are moving a long, nice to see and study how others are doing their custom work, opens up to many different ideas that just might...
    519 replies | 79789 view(s)
  • jamesfr58's Avatar
    06-10-2019, 10:34 PM
    Anyway got back to working on the interior since the bottom half is done, no working on the waterfall testing my upholstery skills. Here it is...
    158 replies | 10253 view(s)
  • jamesfr58's Avatar
    06-10-2019, 10:29 PM
    Well haven't posted in a while as life gets in the way sometimes, the wife and kids wanted a boat for the summer and to go fishing on so after some...
    158 replies | 10253 view(s)
No More Results
About jamesfr58

Basic Information

About jamesfr58
Biography:
Received GTM No. 500 on September 19th, 2017 and began build in October. Engineer by trade always wanted to build one, and finally got chance so here we go...
Location:
Newcastle, Wyoming
Interests:
Cars and collecting them
Occupation:
Semi Retired Refinery Engineer

Statistics


Total Posts
Total Posts
183
Posts Per Day
0.23
General Information
Last Activity
06-22-2019 10:26 PM
Join Date
04-11-2017
Referrals
0

06-15-2019


06-14-2019


Replica Parts

Visit our community sponsor