ReinCarNation

Visit our community sponsor

Tab Content
  • jwebb's Avatar
    Yesterday, 09:18 AM
    Can you MA residents advise who you use for an insurance company/agency for collision, comprehensive & liability for your Roadster?
    7 replies | 108 view(s)
  • jwebb's Avatar
    02-21-2018, 09:58 AM
    jwebb replied to a thread Side Exhaust Position in Roadster
    Just heard from FFR, they are sending a spacer & wedge to get the PS side similar to the DS.. Still don't understand why this condition exists on...
    26 replies | 1198 view(s)
  • jwebb's Avatar
    02-19-2018, 05:11 PM
    jwebb replied to a thread Side Exhaust Position in Roadster
    Norm, Thank you for the reply, I'm more like >1" away on the passenger side! Curious what FFR has to say about the differences side to side. Jim
    26 replies | 1198 view(s)
  • jwebb's Avatar
    02-19-2018, 12:35 PM
    jwebb replied to a thread Side Exhaust Position in Roadster
    Norm, How thick is your spacer and do you feel like making another one?
    26 replies | 1198 view(s)
  • jwebb's Avatar
    02-19-2018, 11:18 AM
    jwebb replied to a thread Side Louvers in Roadster
    Another dumb one: The riveted end of the louver is the front, correct?
    13 replies | 909 view(s)
  • jwebb's Avatar
    02-18-2018, 07:25 AM
    jwebb replied to a thread Side Louvers in Roadster
    Thanks to all, appreciate the info!
    13 replies | 909 view(s)
  • jwebb's Avatar
    02-17-2018, 10:04 AM
    jwebb replied to a thread Side Louvers in Roadster
    Jeff, Are your louvers flush with the outside of the body or flush with the inside? e
    13 replies | 909 view(s)
  • jwebb's Avatar
    02-14-2018, 01:28 PM
    jwebb replied to a thread Side Exhaust Position in Roadster
    da Bat, So you don't use a spacer on the PS to get the header closer to the body, similar to the DS? Just elongating the PS hole is adequate? Jim
    26 replies | 1198 view(s)
  • jwebb's Avatar
    02-12-2018, 01:31 PM
    jwebb replied to a thread Side Exhaust Position in Roadster
    Norm, You wouldn't happen to have the template for the spacer you made, otherwise I'll just us a gasket for the dimensions! Jim
    26 replies | 1198 view(s)
  • jwebb's Avatar
    02-12-2018, 01:22 PM
    jwebb started a thread Side Louvers in Roadster
    The flat ones that come with the kit, tricks/suggestions on bending to get uniform appearance? Or go with the assembled louvers? Curious how the...
    13 replies | 909 view(s)
  • jwebb's Avatar
    02-09-2018, 10:43 AM
    jwebb replied to a thread Side Exhaust Position in Roadster
    Did you add any spacers to the PS? To get the side pipe away from the body enough I'll need to!
    26 replies | 1198 view(s)
  • jwebb's Avatar
    02-09-2018, 08:10 AM
    jwebb replied to a thread Side Exhaust Position in Roadster
    Jeff, How did you address the situation previously? Should I consider shortening the DS header (Mike Everson)if installing the splash shield...
    26 replies | 1198 view(s)
  • jwebb's Avatar
    02-08-2018, 05:44 PM
    jwebb replied to a thread Side Exhaust Position in Roadster
    More room on passenger side?
    26 replies | 1198 view(s)
  • jwebb's Avatar
    02-08-2018, 05:39 PM
    jwebb started a thread Side Exhaust Position in Roadster
    See attached photos, how can I get the exhaust to be the same on both sides? Motor mounts are in the same location left & right in the chassis.....
    26 replies | 1198 view(s)
  • jwebb's Avatar
    02-05-2018, 09:59 AM
    jwebb replied to a thread Body Mounting in Roadster Build Threads
    From manual, page 312: "Move the front of the body as necessary. If the body will not stay where you put it, put a screw through the hood lip of...
    7 replies | 246 view(s)
  • jwebb's Avatar
    02-05-2018, 09:38 AM
    jwebb replied to a thread Body Mounting in Roadster Build Threads
    I have the thin foam cushion provided by FFR on the rails, is that adequate or is there something better? Another question, the brackets that hold...
    7 replies | 246 view(s)
  • jwebb's Avatar
    02-04-2018, 02:50 PM
    Does the body get riveted to the frame rails along the engine compartment?
    7 replies | 246 view(s)
  • jwebb's Avatar
    01-31-2018, 11:56 AM
    jwebb replied to a thread Backup lights in Roadster
    Wiper circuit is 10A, I'll use that instead, thanks!
    33 replies | 1472 view(s)
  • jwebb's Avatar
    01-31-2018, 11:21 AM
    jwebb replied to a thread Backup lights in Roadster
    Since I'm not using the heater circuit, this should work...?
    33 replies | 1472 view(s)
No More Results
About jwebb

Basic Information

About jwebb
Biography:
Just ordered a MK IV roadster kit and will be looking of r some help along the way
Location:
Longmeadow, MA

Signature


MK4 #9121 - Complete kit - Stroked 351, T5x, 3.55 Rear End, 3-Link - Pickup 6/17/17, 1st start 12/2/17, Go-Kart 12/9/17

Statistics


Total Posts
Total Posts
179
Posts Per Day
0.59
General Information
Last Activity
Yesterday 10:51 AM
Join Date
04-25-2017
Referrals
0

Legend Lines

Visit our community sponsor