Miller Customs

Visit our community sponsor

Tab Content
  • Murd's Avatar
    Yesterday, 09:55 PM
    Murd replied to a thread Rear tire to body clearance in Roadster
    It will travel until it hits the bump stops on the shocks. From your ride height I’d say3” travel up, definitely inside the wheel wells. Put the...
    2 replies | 127 view(s)
  • Murd's Avatar
    Yesterday, 06:26 AM
    Same thing, I got a big 56oz one from summit, it’s overkill but not sure if 36oz is quite enough? Probably just.
    4 replies | 201 view(s)
  • Murd's Avatar
    09-17-2018, 10:16 PM
    It’s been widely discussed. You still need to do the bodywork to the point where it’s read for paint, so basically saving the cost of the paint and...
    12 replies | 1020 view(s)
  • Murd's Avatar
    09-16-2018, 07:52 AM
    I used a compression fitting to go from the hardline to AN, but using mechanical fuel pump so low pressure. I believe there are flare to an fittings...
    26 replies | 317 view(s)
  • Murd's Avatar
    09-16-2018, 07:49 AM
    Murd replied to a thread Battery location options in Roadster
    I used the forward mount from breeze and am very happy with it, highly recommended. Moves the weight to a better spot and easy to access. Much easier...
    26 replies | 549 view(s)
  • Murd's Avatar
    09-16-2018, 07:43 AM
    I have a resonant vibration from my engine at about 2100 rpm, anything that can rattle buzzes when rpm crosses that speed. The worst culprit is the...
    4 replies | 254 view(s)
  • Murd's Avatar
    09-14-2018, 08:59 PM
    Murd replied to a thread Blew up T5 in Roadster
    Yes that is him, spoke to a couple other guys that used him too, good guy.
    19 replies | 1100 view(s)
  • Murd's Avatar
    09-13-2018, 06:43 PM
    Murd replied to a thread Blew up T5 in Roadster
    Finished putting her back together tues night, back on the road yesterday. Great to be back driving and the taller 2.95 first gear is a huge...
    19 replies | 1100 view(s)
  • Murd's Avatar
    09-11-2018, 07:44 PM
    Murd replied to a thread 3 link question in Roadster
    You’ve got it. Just set ride height and pinion angle. I’d suggest checking the toe on your rear end. I was basically done and went to align the car,...
    7 replies | 326 view(s)
  • Murd's Avatar
    09-10-2018, 11:01 AM
    Murd replied to a thread Blew up T5 in Roadster
    Thanks guys, got it back in and 90% put back together then had to go away on business for a week. Flying home now, can’t wait to get it done and back...
    19 replies | 1100 view(s)
  • Murd's Avatar
    09-04-2018, 12:06 PM
    Duplicate
    6 replies | 245 view(s)
  • Murd's Avatar
    09-04-2018, 07:47 AM
    I have the same linkage and spent a ton of time on this. IMHO pedal placement is one of the most important parts of the build. I drilled different...
    6 replies | 245 view(s)
  • Murd's Avatar
    09-03-2018, 07:56 PM
    Murd replied to a thread Nagging Oil Leak in Roadster
    I had a similar valve cover leak. On the mechanic who saftied my car’s recommendation I used the right stuff sealant between my silicone permadry...
    23 replies | 716 view(s)
  • Murd's Avatar
    09-02-2018, 11:53 AM
    I would suggest not bolting it on at this stage. I mounted my steering wheel to it and just slid it on the shaft enough to be able to use the...
    7 replies | 254 view(s)
  • Murd's Avatar
    09-02-2018, 07:12 AM
    I feel like this was in the back of the manual for optional rear brakes and showed putting the brackets together. I have the same brakes but got them...
    3 replies | 150 view(s)
  • Murd's Avatar
    08-31-2018, 08:12 AM
    Murd replied to a thread Overflow tank Options in Roadster
    I had the stock FFR tank and it would overflow even from empty with a 302. I put on one from summit that I believe was 56oz, it’s overkill but rather...
    18 replies | 526 view(s)
  • Murd's Avatar
    08-31-2018, 07:40 AM
    Thanks everyone for the replies, I put headers back on last night with copper RTV, hopefully works as well for me as everyone else. I liked JR’s...
    10 replies | 352 view(s)
  • Murd's Avatar
    08-29-2018, 02:58 PM
    Thanks, Any tips? Guessing just a light bead? Don’t want to be filling up my exhaust ports.
    10 replies | 352 view(s)
  • Murd's Avatar
    08-29-2018, 02:31 PM
    Just pulled engine to install new transmission. I have the bbk 4 into 4 headers from FFR, for the header gasket, and header to side pipe gasket,...
    10 replies | 352 view(s)
  • Murd's Avatar
    08-29-2018, 02:23 PM
    Murd replied to a thread Blew up T5 in Roadster
    Just went yesterday and picked up my new T5 I had built. Basically built to T5z spec with 2.95 1st gear, moly hardened gears, new syncrotech carbon...
    19 replies | 1100 view(s)
  • Murd's Avatar
    08-25-2018, 11:04 AM
    Gumball, Seat of your pants which one feels quicker? Power to weight for a gt350 approx 7lbs/hp, 2200lb 350hp FFR is 6.3. Mine is probably about...
    27 replies | 700 view(s)
  • Murd's Avatar
    08-25-2018, 10:52 AM
    Murd replied to a thread A Basic Rookie question..... in Roadster
    Do they put ethanol alcohol in your fuel there? I put in shell 91 here in Canada as I know it doesn’t have ethanol. It does all kinds of bad things...
    14 replies | 564 view(s)
No More Results
About Murd

Basic Information

About Murd
Biography:
Building a FFR MK4 I picked up in Feb, From Ontario Canada.

Statistics


Total Posts
Total Posts
157
Posts Per Day
0.42
General Information
Last Activity
Yesterday 09:56 PM
Join Date
09-10-2017
Referrals
0

09-16-2018


09-15-2018


08-25-2018


Replica Promotions

Visit our community sponsor