Very Cool Parts

Visit our community sponsor

Tab Content
  • Dwleo's Avatar
    05-18-2019, 08:58 PM
    Dwleo replied to a thread Leaky Diff in Roadster
    Yeah, I know. But they are about 45 minutes away in city traffic and the roadster isn't ready for that yet. Also we are going away for a few weeks...
    3 replies | 140 view(s)
  • Dwleo's Avatar
    05-18-2019, 12:38 PM
    Dwleo replied to a thread Body Fit and lasered holes in Roadster
    Today is one of the backwards steps that seem almost necessary in these builds. Off come the over riders, drop the tank and off come the rear ones. ...
    17 replies | 545 view(s)
  • Dwleo's Avatar
    05-18-2019, 12:17 PM
    Dwleo started a thread Leaky Diff in Roadster
    I had my diff built by a local manufacturer (very reputable) last November. The invoice listed all they did which included filled it with gear oil. I...
    3 replies | 140 view(s)
  • Dwleo's Avatar
    05-16-2019, 10:54 AM
    Dwleo replied to a thread Body Fit and lasered holes in Roadster
    Here's a pic of the header opening. (ooops. upside down)
    17 replies | 545 view(s)
  • Dwleo's Avatar
    05-16-2019, 10:47 AM
    Dwleo replied to a thread Body Fit and lasered holes in Roadster
    The body cannot go forward anymore unless I cut off a portion of the trunk floor (it's right tight there) and then cut down the spacers on the...
    17 replies | 545 view(s)
  • Dwleo's Avatar
    05-16-2019, 09:57 AM
    Dwleo replied to a thread Body Fit and lasered holes in Roadster
    The body cannot go forward anymore unless I cut off a portion of the trunk floor (it's right tight there) and then cut down the spacers on the...
    17 replies | 545 view(s)
  • Dwleo's Avatar
    05-16-2019, 09:51 AM
    Dwleo replied to a thread Body Fit and lasered holes in Roadster
    Yeah, I wondered about that when they would not line up. Measured the overriders and they were both the same. Measured the body openings and the...
    17 replies | 545 view(s)
  • Dwleo's Avatar
    05-15-2019, 09:37 PM
    Dwleo replied to a thread Body Fit and lasered holes in Roadster
    Motors balanced and the height is the same. Something I checked during the go-cart stage
    17 replies | 545 view(s)
  • Dwleo's Avatar
    05-15-2019, 08:46 PM
    Well, today the body went on and it was fairly straight forward except that even though the body is fitted tight at the bottom of the trunk and the...
    17 replies | 545 view(s)
  • Dwleo's Avatar
    05-01-2019, 09:57 AM
    Dwleo replied to a thread Clutch Cable Fraying in Roadster
    The problem is that the angle is the opposite. Can't bend the 'hole' for that angle.
    6 replies | 376 view(s)
  • Dwleo's Avatar
    04-30-2019, 07:25 PM
    Dwleo started a thread Clutch Cable Fraying in Roadster
    Here I post again. I noticed my clutch cable is fraying on the quadrant arm. I haven't even gone karting yet, just been and out of the garage a...
    6 replies | 376 view(s)
  • Dwleo's Avatar
    04-29-2019, 12:10 PM
    Mike is selling the cables that are NOT adjustable, as stated in this email from him. "THESE ARE STOCK MUSTANG CABLES FROM THE M-7553-A302 KIT....
    18 replies | 773 view(s)
No More Results
About Dwleo

Basic Information

About Dwleo
Biography:
Working on second roadster. Built a '23 T-Bucket between builds.

Statistics


Total Posts
Total Posts
34
Posts Per Day
0.38
General Information
Last Activity
Today 12:11 PM
Join Date
02-19-2019
Referrals
0

05-01-2019


Martin's Dent and Collision Shop

Visit our community sponsor