View Profile: chrisarella - Factory Five Forums

Yesterday, 11:55 PM

chrisarella replied to a thread Rear quick jack mounting in Roadster

Thanks for the tips.

26 replies | 9650 view(s)

Yesterday, 10:59 PM

edwardb replied to a thread Coyote in a 33, CMCV question in Engine & Transmission - 33 HotRod

Hey Henry. Most of the Mustang tuner sites have CMCV lockout parts for Coyotes. Pretty simple and not too expensive. They are different depending on...

1 replies | 15 view(s)

Yesterday, 04:05 PM

chrisarella replied to a thread Rear quick jack mounting in Roadster

Great suggestions guys. I wanted stainless because I'm in Florida where it extremely humid and I'd lose my mind if I looked in the trunk and saw rust...

26 replies | 9650 view(s)

Yesterday, 02:28 PM

chrisarella replied to a thread Rear quick jack mounting in Roadster

What size coupler nuts, rods and bolts are you using. I'm having a really hard time finding 7/16-20 for all of the pieces as others have used. My...

26 replies | 9650 view(s)

Yesterday, 07:39 AM

edwardb replied to a thread Forte Hydrualic Clutch Alignment Question in Roadster

1. Looks like machining wasn't quite finished on that rod end. Cut it off and smooth it out. 2. Some variations in setup so can't recommend a...

21 replies | 522 view(s)

02-15-2019, 04:32 PM

edwardb replied to a thread Edwardb’s Gen 3 Type 65 Coyote Coupe #59 Build: Body On and Fitting Underway in Type '65 Coupe Build Threads

Sorry about that. Throw out acronyms and forget not everyone always recognizes them. 3M High Strength Repair Filler. A vinyl ester based product...

549 replies | 130113 view(s)

02-15-2019, 12:26 PM

edwardb replied to a thread Edwardb’s Gen 3 Type 65 Coyote Coupe #59 Build: Body On and Fitting Underway in Type '65 Coupe Build Threads

Couple buddies dropped over the other night, and around an hour plus of shop talk, spent the five minutes needed to drop the front and rear body...

549 replies | 130113 view(s)

02-15-2019, 11:37 AM

edwardb added 1 photo(s) to album Gen 3 Type 65 Interior

02-15-2019, 11:36 AM

edwardb added 4 photo(s) to album Gen 3 Type 65 Coupe Body

02-14-2019, 04:57 PM

edwardb replied to a thread Adding new circuits to the standard Ron Francis wire harness and panel in Electrical - 33 HotRod

No way to add additional circuits to the provided RF panel that I'm aware of. I haven't tried and haven't seen anyone else try it either. But you...

7 replies | 174 view(s)

02-13-2019, 03:41 PM

edwardb replied to a thread Brake line route question in Roadster Build Threads

No. Orient the fittings however works best for your planned brake line routing. No picture showing here either BTW.

15 replies | 334 view(s)

02-13-2019, 07:14 AM

edwardb replied to a thread Coyote with stock ford 6 speed in Roadster

Off topic but I'll throw it out there anyway. A month or so ago we had an open house here with our club members checking out my Coupe build. Two guys...

23 replies | 873 view(s)

02-12-2019, 11:44 PM

edwardb replied to a thread Edwardb’s Gen 3 Type 65 Coyote Coupe #59 Build: Body On and Fitting Underway in Type '65 Coupe Build Threads

I said the next update would be with the body on. I guess I lied. Decided before I did that to complete my first alignment. Although not as much the...

549 replies | 130113 view(s)

02-12-2019, 10:54 PM

edwardb added 7 photo(s) to album Gen 3 Type 65 Coupe Chassis

02-12-2019, 09:42 PM

Rootbeer Roadster replied to a thread Engine choice input wanted. in Roadster

When I built my Roadster I wanted a car that was very quick from 0 to 60, well mannered, agile and fun to drive. The purpose was to take drives on...

63 replies | 1346 view(s)

02-12-2019, 12:42 PM

edwardb commented on article EdwardBs Mk4 #8674 20th Anniversary Build in Roadster

That material might work. But what I actually use is Permatex 81878 Utra Copper. Also use it on the header to pipe connection instead of gaskets....

709 replies | 3967 view(s)

02-12-2019, 12:38 PM

edwardb replied to a thread What happens when I need to tow my Coupe? in Type '65 Coupe

An experienced driver/operator shouldn't have a problem with it. Yes, it's low in the front but so are lots of other specialty cars they deal with....

4 replies | 245 view(s)

02-12-2019, 09:52 AM

chrisarella replied to a thread Driveshaft Loop in Roadster

Thanks Martin. Are these in stock? And will it work with the extra short driveshaft in a T56-Magnum/IRS setup? BTW, just an observation... you...

65 replies | 3082 view(s)

02-11-2019, 09:55 PM

edwardb commented on article EdwardBs Mk4 #8674 20th Anniversary Build in Roadster

Flush rivets worked great there. Not having the head of the rivet above the surface allows the trans cover to fit nicely. I used these from McMaster:...

709 replies | 3967 view(s)

02-11-2019, 09:51 PM

chrisarella replied to a thread Driveshaft Loop in Roadster

It isn't on the site. Just call him.

65 replies | 3082 view(s)

02-11-2019, 09:46 PM

edwardb replied to a thread Patrick's 427 Build in Roadster Build Threads

I've done a couple on jack stands. It's OK, but I can see the attraction of the dolly. The other two I've done with a 2-post lift. Now that's how to...

37 replies | 998 view(s)

chrisarella
Senior Member

Mini Statistics

More 2 Friends

Rootbeer Roadster

edwardb

1 Groups

Southern Super Snakes (SSS)

Join Groups 0 Permission Groups

Recent Visitors

Basic Information

About chrisarella

Signature

Contact

Instant Messaging

Statistics

Total Posts

General Information

2 Friends

edwardb

Rootbeer Roadster

02-16-2019

02-11-2019

chrisarella Senior Member

Mini Statistics

More 2 Friends

Rootbeer Roadster

edwardb

1 Groups

Southern Super Snakes (SSS)

Join Groups 0 Permission Groups

Recent Visitors

Basic Information

About chrisarella

Signature

Contact

Instant Messaging

Statistics

Total Posts

General Information

2 Friends

edwardb

Rootbeer Roadster

02-16-2019

02-11-2019

chrisarella
Senior Member