Very Cool Parts

Visit our community sponsor

Search:

Type: Posts; User: JimLev

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. When I lived in MA (another liberal state) in...

    When I lived in MA (another liberal state) in addition to a 6.2% sales tax on the purchase price (no cap) we had a yearly excise tax that you pay forever. Plus a yearly safety and emission test.
    ...
  2. Replies
    1
    Views
    152

    You probably don't need all of them, depends on...

    You probably don't need all of them, depends on the engine you are using and what gauges you have.
    I used some of them, had to cut off the connectors any use terminals for the Autometer gauges.
  3. Replies
    87
    Views
    5,854

    I used the mount supplied by FFR, made a few mods...

    I used the mount supplied by FFR, made a few mods to it and added spacers.

    110570
  4. Replies
    87
    Views
    5,854

    I raised the bottom of the seat frame 6" off the...

    I raised the bottom of the seat frame 6" off the floor. Much easier to see the right front corner of the car now.
    I think I'll still have ar least 2" above my head to the top (it's not on yet)
  5. Replies
    8
    Views
    396

    My gap at the top of the firewall to the body is...

    My gap at the top of the firewall to the body is only 1/16". I have the steering column adjusted up as high as possible, it just touches the bottom of the dash. I'm OK with both.
    I do have a 1/4"...
  6. Replies
    8
    Views
    396

    Andy, what are we looking in the 3rd and 4th...

    Andy, what are we looking in the 3rd and 4th pics?

    The gap between the body and the frame at the back rear above the fuel tank?
    I've got that too, there is a piece of rolled up 1" foam (one side...
  7. Replies
    87
    Views
    5,854

    Your box is much different than mine. My control...

    Your box is much different than mine.
    My control box only has 3 sockets on it. It's a UniSteer/Electra-Steer kit, p/n 8051500.
    One connector for the steering motor, one for the steering position...
  8. Replies
    87
    Views
    5,854

    Is that the control box that came with the...

    Is that the control box that came with the electric steering from FF?
    There's a green wire in your first pic, where does the other end of the green wire go? Is it taped up?
    My box came from...
  9. Replies
    87
    Views
    5,854

    [QUOTE=colsen23153;371853] 109386 I like...

    [QUOTE=colsen23153;371853]

    109386

    I like that open/removable dash opening, wish the Gen 1 had it. I'm seriously thinking about cutting mine and then finding a metal sheet to mount the gauges...
  10. Replies
    57
    Views
    2,678

    And what are all of those projections on the top?...

    And what are all of those projections on the top? To keep it from getting stuck under tool boxes and other low things?
    My wife has a iRobot Roomba that I used in the garage once, it's low but can...
  11. Replies
    58
    Views
    3,142

    Thanks for the pic and info AJT. Last night I...

    Thanks for the pic and info AJT. Last night I ordered resin and mat. Think I'll do some glassing before the sanding.
  12. Not a FF5 Cobra but thought you might like to see it

    Last weekend a bunch of us from our local car club went up to Durango for a yearly get together.
    My '33 wasn't finished so I rode in and drove a friends '66 Vette.
    This Cobra is polished aluminum,...
  13. Replies
    58
    Views
    3,142

    Here's what will need some work on to make it...

    Here's what will need some work on to make it look decent.
    109034

    The other issue with both doors is the rear lower corner, it hits the body before the door closes, maybe some door seals will...
  14. Replies
    58
    Views
    3,142

    They sent me a replacement drivers door, it was a...

    They sent me a replacement drivers door, it was a little better than the original. I still needed shims to make it align with the body.
    The top front of the door is off a bit where it meets the...
  15. Replies
    17
    Views
    1,079

    Mine is mounted horizontally, didn't have any...

    Mine is mounted horizontally, didn't have any problems with it reading the correct pressure.
    We have different engine so it's apples to oranges comparison.
  16. Replies
    12
    Views
    1,021

    Ditto

    Ditto
  17. Replies
    54
    Views
    2,691

    Have fun, enjoy the build. Good to see your...

    Have fun, enjoy the build.
    Good to see your using an LS, lots of potential upgrades can be found everywhere.
  18. Thread: JimLev's Build

    by JimLev
    Replies
    280
    Views
    31,750

    No problem Nevin, the forum is here so we can all...

    No problem Nevin, the forum is here so we can all help each other.
    I'll be bugging others soon about resin and fiberglassing.
  19. Replies
    1
    Views
    270

    Maybe have summit replace it? You could possibly...

    Maybe have summit replace it?
    You could possibly add a resistor to make the gauge read correctly.
  20. Thread: JimLev's Build

    by JimLev
    Replies
    280
    Views
    31,750

    Kamp, thanks for the info, it should help others....

    Kamp, thanks for the info, it should help others.
    I bought the electric steering from FFR when I ordered my car, when they had the 1/2 price sale.

    108739
  21. Thread: JimLev's Build

    by JimLev
    Replies
    280
    Views
    31,750

    Nice bracket. Who made the electric steering...

    Nice bracket. Who made the electric steering motor?
  22. Thread: JimLev's Build

    by JimLev
    Replies
    280
    Views
    31,750

    It's been a while since I updated my build. Don't...

    It's been a while since I updated my build. Don't really have much to show as I've been avoiding doing fiberglass work.
    I put the insulation and sound deadening on the tranny tunnel a few days ago....
  23. Connect the ground wires together inside the...

    Connect the ground wires together inside the headlight bucket.
  24. I hate leaks too. Any of you with older BMW's...

    I hate leaks too. Any of you with older BMW's know the gaskets are crap. They only recommend using a sealant on certain sections of the gaskets.
    For the last 10 years I've been using Hylomar on the...
  25. Replies
    45
    Views
    2,646

    Shop and engine look great. While your waiting...

    Shop and engine look great. While your waiting for Stewart epoxy the floor, so much easier to keep clean.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

Flat Irons Tuning

Visit our community sponsor