Midwest Classic Insurance

Visit our community sponsor

Search:

Type: Posts; User: JOP33

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    497
    Views
    70,740

    Finally, Kory and I are toying around with a few...

    Finally, Kory and I are toying around with a few ideas regarding the hood as well, but I am not committed to doing anything (or nothing) as of yet...I need to visualize a few things first...Will post...
  2. Replies
    497
    Views
    70,740

    The highlight of the week for me was seeing the...

    The highlight of the week for me was seeing the Headwinds installed on the car...to me they just compliment the grill of the car so well (lots of pics here, so be patient)...

    107576

    107577
    ...
  3. Replies
    497
    Views
    70,740

    Here is the weekly update...Tim Whittaker's Deck...

    Here is the weekly update...Tim Whittaker's Deck Lid Stiffeners were used on the trunk. Abel was inset them into the trunk with some panel bond then used screws on the top side to fine-tune the...
  4. Replies
    497
    Views
    70,740

    Did receive some feedback from Tony @ FFR...

    Did receive some feedback from Tony @ FFR regarding the location of the Prop Rod on the Extra Clearance Hood...he referenced the Flame car where he attached the Hood Prop on the fire wall so the...
  5. Thread: Texas Saga

    by JOP33
    Replies
    38
    Views
    8,326

    Where are you out of in Texas?

    Where are you out of in Texas?
  6. Replies
    497
    Views
    70,740

    cont'd... 107042 107043 107044 107045

    cont'd...

    107042

    107043

    107044

    107045
  7. Replies
    497
    Views
    70,740

    I know that most of ya'll understand the concept...

    I know that most of ya'll understand the concept of "no" or "little visual update"...meaning that work has transpired but it may appear as if progress has not be made. There are sooooo many little...
  8. Replies
    1
    Views
    131

    Extra Clearance Hood & Prop Rod Location

    Reaching out to those of you that opted for the Extra Clearance Hood...Any suggestions on where to mount the prop rod? The manual shows the supports that run down the middle of the hood , however...
  9. Replies
    13
    Views
    392

    Congratulations! And if you are building it in a...

    Congratulations! And if you are building it in a garage or shop in the middle of the Summer here in Texas you will have even a greater appreciation for the AC when done!

    Good luck and enjoy!
  10. Replies
    3
    Views
    220

    I believe the front horns on the body also get...

    I believe the front horns on the body also get attached to the triangular kick up front.
  11. Replies
    497
    Views
    70,740

    Going with electric locks from Carolina...

    Going with electric locks from Carolina Customs...will follow up with more details on the "how" soon

    ...
  12. Replies
    497
    Views
    70,740

    Just a few items worth mentioning this week. Kory...

    Just a few items worth mentioning this week. Kory and Abel got the new cutouts done and the 39' tail lights installed and I really like this look!

    106737

    106738

    106739

    106740
  13. Replies
    5
    Views
    275

    Congratulations, let the fun begin!

    Congratulations, let the fun begin!
  14. Replies
    497
    Views
    70,740

    Summit Racing...63100-VUQ, aluminum

    Summit Racing...63100-VUQ, aluminum
  15. Replies
    497
    Views
    70,740

    cont'd... Door Pull cut outs... 106423 ...

    cont'd...

    Door Pull cut outs...
    106423

    Vent cuts & install...
    106424
  16. Replies
    497
    Views
    70,740

    So another good week of progress from 121 Rod &...

    So another good week of progress from 121 Rod & Restoration this week. Since the Headwinds Headlights have been delayed slightly (the Chromer that Headwinds uses ran over the turn signal and crushed...
  17. Replies
    78
    Views
    7,097

    I had (have) some similar issues with my set-up,...

    I had (have) some similar issues with my set-up, in fact the throttle cable still is not straight in line. I will need to make or purchase a longer mounting bracket in the rear to offset the cable a...
  18. Thread: #998 Build Page

    by JOP33
    Replies
    171
    Views
    23,278

    Nice job on the Dynamat! I think that will pay...

    Nice job on the Dynamat! I think that will pay off.
  19. Replies
    497
    Views
    70,740

    I did make it by the shop yesterday and saw some...

    I did make it by the shop yesterday and saw some really good progress. The roadster windshield had been previously located, so this week they cut the access panels for the M/C Covers and installed...
  20. Replies
    497
    Views
    70,740

    Will try to make it up to the shop today...I have...

    Will try to make it up to the shop today...I have re-cut the Master Cylinder Covers out of 1/8" Aluminum to allow for the guys to recess the cover flush with the body opposed to sitting on top of the...
  21. Replies
    17
    Views
    850

    Enjoy and have fun!

    Enjoy and have fun!
  22. Replies
    497
    Views
    70,740

    Made it out to 121 R & R for an update this...

    Made it out to 121 R & R for an update this week...not a lot of sexy things going on, meaning the details that Kory and his team are working through now don't really make for good pics, but I took...
  23. Replies
    497
    Views
    70,740

    For the easy stuff, I use DraftSight (freeware...

    For the easy stuff, I use DraftSight (freeware and a really good CAD package)...for the more difficult stuff, SolidWorks.
  24. Replies
    497
    Views
    70,740

    Not a lot to update from last week, but the trunk...

    Not a lot to update from last week, but the trunk did get fit-up...and that in itself was a challenge according to the shop. For those of you that are doing your on panel fit-up, body work and...
  25. Replies
    64
    Views
    10,334

    Nice ride bud! Congratulations.

    Nice ride bud! Congratulations.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

Lodestone Billetworks

Visit our community sponsor