ReinCarNation

Visit our community sponsor

Search:

Type: Posts; User: Robodent

Page 1 of 4 1 2 3 4

Search: Search took 0.66 seconds.

  1. Replies
    51
    Views
    2,926

    I had the same issue. What I tried was to loosen...

    I had the same issue. What I tried was to loosen the crash beam from the latch bracket twist the door where it needs to go and re tighten everything.
  2. Replies
    6
    Views
    624

    Sorry I forgot to insert the picture 110853110853

    Sorry I forgot to insert the picture 110853110853
  3. Replies
    6
    Views
    624

    I’ve been busy at work the past couple months and...

    I’ve been busy at work the past couple months and slacking on my build a bit. I have everything painted other than the cab and the doors. Here’s a sneak peek at what I did to my air cleaner. My...
  4. I will be there Saturday the 27th. Looking...

    I will be there Saturday the 27th. Looking forward to meeting Eric and the crew.
  5. Replies
    2
    Views
    172

    Yes I ran into issues as well there. What I did...

    Yes
    I ran into issues as well there. What I did was cut the carriage bolt down and got a new half but to make it work.
  6. This kinda feels like Craig’s list with multiple...

    This kinda feels like Craig’s list with multiple post with the same ads
  7. Replies
    5
    Views
    208

    Ron. I cut my hinge slot holes before I dropped...

    Ron. I cut my hinge slot holes before I dropped the cab on. The hinge brackets go on before the cab goes on the striker bracket I installed after the cab was on and then drilled my striker hole...
  8. Welcome!!! Have fun with your build . I’m in...

    Welcome!!! Have fun with your build . I’m in hampshire Il not to far away building a 35 truck. Good luck to you. Rob
  9. Replies
    8
    Views
    318

    Well when I installed the quarter panels first I...

    Well when I installed the quarter panels first I pretty much shoved them all the way forward to the cab about an inch or less to the cab. Drilled my front hole on the quarter which ended up inside...
  10. Replies
    8
    Views
    318

    I believe your correct on the tailgate top bar...

    I believe your correct on the tailgate top bar it’s the flared out extension of the tailgate itself. The bottom tailgate is the lower roll pan. Take my advice or leave it but I cut the roll pan in...
  11. Replies
    25
    Views
    2,126

    Thanks for the post. I’ve been comptinplating...

    Thanks for the post. I’ve been comptinplating on weather or not to go with wipers but I might have to here in Illinois to get through inspection. I’m at the crossroads right now with body work and...
  12. Thread: New to FFR

    by Robodent
    Replies
    17
    Views
    825

    Congratulations Have fun with your build

    Congratulations
    Have fun with your build
  13. I’m in hampshire building a truck almost done...

    I’m in hampshire building a truck almost done with the body work. Pm me anytime I have 30 years of body experience. My dest advice is don’t compromise anything start to finish. Rob
  14. Replies
    6
    Views
    382

    Welcome, have fun building.

    Welcome, have fun building.
  15. Replies
    124
    Views
    14,791

    Congrats

    Congrats
  16. Replies
    10
    Views
    544

    Welcome, have fun with your build. Don’t...

    Welcome, have fun with your build. Don’t compromise. Rob
  17. Replies
    4
    Views
    296

    Yes I have the optima 9078-109 side post bought...

    Yes I have the optima 9078-109 side post bought it new from summit. Rob
  18. Replies
    4
    Views
    296

    I have the odyssey as well imo it’s junk. I’m...

    I have the odyssey as well imo it’s junk. I’m switching to a optima side terminal only no top post otherwise it will be to tall

    Rob
  19. Replies
    53
    Views
    4,594

    Looks good . I have the same diff cover and...

    Looks good . I have the same diff cover and wait till you set it on the ground the diagonal bar on the frame from the passenger side panhard to the drivers side upper frame rail will hit the top of...
  20. Replies
    6
    Views
    624

    Truck progress

    Made some progress last weekend on my truck. Installed the bed and fitted the front cowl and dash. Feels great to see it all together and take shape. Next im going to install the power windows and...
  21. Thanks for posting this. Love seeing the truck...

    Thanks for posting this. Love seeing the truck builds and what others have done with them. Rob
  22. Replies
    124
    Views
    14,791

    Great job !!!! No biggie on the glass it will...

    Great job !!!! No biggie on the glass it will need to come back out to paint anyway the final fit is the important one. Good luck on your inspection. Did you install wipers ? I’m in Illinois...
  23. Replies
    10
    Views
    633

    I hear you ken, I’m not happy either sitting on...

    I hear you ken, I’m not happy either sitting on top of a muffler. I used some sticky aluminum heat shield on the bottom side of the floor pan I got from summit. And using the heat shield that came...
  24. Replies
    3
    Views
    355

    Not much leg room I’m 6 1” and it’s tight I...

    Not much leg room
    I’m 6 1” and it’s tight I cut my cross bar out and pushed my seat all the way back to the rear of the cab and got a little more out of it. Rob
  25. Replies
    210
    Views
    18,932

    Looks great ! Nice job.

    Looks great ! Nice job.
Results 1 to 25 of 80
Page 1 of 4 1 2 3 4

Replica Parts

Visit our community sponsor