Very Cool Parts

Visit our community sponsor

Search:

Type: Posts; User: gnd_hog

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. All the Vette mods logged in videos on my...

    All the Vette mods logged in videos on my
    Channel - Coupe videos will go up there as well.

    Vette will end up around 5:1 lbs/wHP - Coupe will be less than 3:1....

    https://youtu.be/lnFopqZM-Pc
  2. Hopefully Gordon will get some photos to me soon...

    Hopefully Gordon will get some photos to me soon - frame should be ready for powder coating then assembly starts.

    Have told him do it right and don’t rush - have the vette to play with for now.......
  3. Vette getting plenty of similar parts to the...

    Vette getting plenty of similar parts to the Coupe - including the rear wing. Vette wing picture below.

    Coupe frame getting closer to powder coat - Gordon has redesigned the front section several...
  4. Gordon get close to send chassis off for powder...

    Gordon get close to send chassis off for powder coat

    Been tweaking on my ZR1 getting her better prepped for track life as well...



    https://youtu.be/_5x-6140ECM
  5. The non-ludicrous setting of 800 rwhp will give...

    The non-ludicrous setting of 800 rwhp will give more power to weight ratio than a GT series racecar - and should be more than adequate to push me around the track for some time until I learn to...
  6. Fully aware the AEM will allow adjustable input/s...

    Fully aware the AEM will allow adjustable input/s - question was more to base them off of achieved HP or just boost psi limits. Dial a given HP or dial a given boost or level (really the same just a...
  7. thoughts on how to vary adjustable engine tunes. ...

    thoughts on how to vary adjustable engine tunes. Very easy to have cockpit mounted knob to move between settings - should be on the fly adjustable as well.....

    Original thought was to have 800,...
  8. Pictures will come - Gordon trying to get all...

    Pictures will come - Gordon trying to get all frame mods done then will take some shots when everything "fits"

    There will be 6 vent ducts running through front air dam (fog light holes will get...
  9. Turbos placed - just in front of foot boxes -...

    Turbos placed - just in front of foot boxes - left/right twin Borg Warner EFR-8374-1.05 non waste gate. Gordon tried the Garrett 71mm's - but didn't fit - just too big of diameter....

    The Borg...
  10. Transmission bell housing a little wide - some...

    Transmission bell housing a little wide - some frame tubing will need "adjusted" - looks like 32 gal fuel cell fits without issue - waiting on getting some photos still - will add as soon as I get...
  11. Replies
    0
    Views
    817

    GTF body fitment

    Will the new GTF body will an easy drop on an existing Gen 3 Coupe OR Gen 3 Coupe R frame? Will it be available as body kit only? (to retrofit on an existing Gen 3 Coupe or Coupe R)

    the little...
  12. Transmission getting fitted in tunnel - mounting...

    Transmission getting fitted in tunnel - mounting a now 32 gal fuel in the rear - along with dry sump tank in the back / and figuring out where to put half a dozen various exchangers will be first on...
  13. 96333

    96333
  14. Well - Stewart transport had some issues and...

    Well - Stewart transport had some issues and body/chassis sitting at warehouse in Phoenix - some 65 miles away from Gordon - but hopefully, almost, maybe car will get started on this week.....maybe...
  15. GndHog's Gen 3 Coupe-R Coyote XS 5.2 twin turbo build by LR Classics

    Moving build thread here as hopefully Gordon will get chassis this week and away we'll go. Worked and rework some build points on car - have pretty much set plan now baring any unforeseen issues...
  16. Thread: 5.2 or 5.4

    by gnd_hog
    Replies
    23
    Views
    1,482

    Hopefully, my chassis will show up at Gordonís...

    Hopefully, my chassis will show up at Gordonís this week and heíll get started on build. 5.2 XS with twin turbos - purpose built for track use only. Looked a lot a flat plane crank but without a...
  17. Replies
    66
    Views
    6,486

    Still no chassis yet for Gordon to get started...

    Still no chassis yet for Gordon to get started on...... :(

    And FFR powder coated the tube chassis when they were supposed to leave bare (several frame mods will occur)......
  18. Replies
    6
    Views
    525

    there will be a REALLY fast Coupe-R in NASA SU...

    there will be a REALLY fast Coupe-R in NASA SU hopefully by mid-next year........really fast.....:)
  19. Replies
    66
    Views
    6,486

    Rolling back cams and phasers to gen 2, Ford...

    Rolling back cams and phasers to gen 2, Ford performance has set that are same lift/duration specs as in the XS, will work with AEM perfectly for VVT adjustments. Both builder and tuner are happy...
  20. Replies
    66
    Views
    6,486

    Car is getting auto trans vs. manual - with the...

    Car is getting auto trans vs. manual - with the paddle shifters and between the independent transmission shift controller and the AEM infinity - we should be able to implement a no lift shift type...
  21. Replies
    66
    Views
    6,486

    Pictures will come as soon as chassis shows up -...

    Pictures will come as soon as chassis shows up - hopefully mid-late august. Snapping photos of a tranny in a shipping crate and a fuel cell, etc laying just doesn't excite Gordon that much.....:)
    ...
  22. Replies
    66
    Views
    6,486

    Trans tunnel will be tight for sure - he has...

    Trans tunnel will be tight for sure - he has transmission there already but no chassis yet. Fitting tranny first of many obstacles to overcome. Car is getting a custom made driveshaft so there's...
  23. Replies
    66
    Views
    6,486

    Brakes agreed to - 372x34 AP9668 caliper front...

    Brakes agreed to - 372x34 AP9668 caliper front and 365x30 AP9449 caliper rear - full custom made hats and mount brackets from Essex parts - will ship them front/rear knuckles with hubs.....car must...
  24. Thanks Joe - I think I have it sorted out now...

    Thanks Joe - I think I have it sorted out now without needed to send someone to give car once over. Videos and FaceTime are great tools.....
  25. Need some help from someone in Miami FL area

    Help -

    Found a car I want to get as back-up for Coupe-R thatís getting built.

    Car is located in Miami FL - just need someone to go by and check out car before I pull plug and purchase. Will...
Results 1 to 25 of 64
Page 1 of 3 1 2 3

Brown County Customs

Visit our community sponsor