Forte's

Visit our community sponsor

Thanks Thanks:  29
Likes Likes:  38
Page 1 of 17 12311 ... LastLast
Results 1 to 40 of 779

Thread: EdwardBs Mk4 #8674 20th Anniversary Build

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    10,547
    Post Thanks / Like

    EdwardBs Mk4 #8674 20th Anniversary Build

    April 2020: Table of Contents posted on last page. Link

    June 2019: 5,000 mile report posted. Link


    Time to get rolling on another build thread. After a 1,680 mile round trip from Michigan to Wareham, as of August 6, 2015, Mk4 #8674 is now sitting in our garage. This is a 20th Anniversary Edition Mk4, number 03 of 20. This will be my third Roadster build, but a significant first. This is the first build where I am the original owner and taking delivery directly from Factory Five. The first two were purchased from their first owners as partial builds. The Mk3 had a good head start by a pro builder, so a great introduction. The Mk4 was only several months started, so almost like a new build. But time to go it alone from the very beginning. Plus Michigan gave me a really tough time the last go around without my name on the Certificate of Origin. So not going there again.

    I thoroughly enjoy driving the completed Roadsters, going to car shows, and cruising whenever I get the chance. Absolutely a blast. The social aspect is great too, with our local club, the extended forum and Factory Five community, etc. But I also really enjoy the whole learning, planning and building process. Each time the builds were completed, I found myself missing the building. With my retirement earlier this year, it didn’t take long to realize another build was something I wanted to do. After some studying (and soul searching) decided it had to be another Roadster, and just to change it up a little spent quite a bit of time planning a 289 FIA build. I was ready to order one during the 50/50 sale several months ago. But then the 20th Anniversary Edition Mk4 was announced, and I was immediately hooked. I called and ordered it while at a rest stop in New York on the way to this year’s Factory Five open house, just minutes after it was made available for purchase. The plan is to sell #7750 when the new build is completed. #7750 is in it's first driving season this year, and now all sorted out and truly a pleasure to own and drive. Frankly, I can’t imagine letting go of it. But that’s the deal, and I’m sticking to it.

    So let’s get down to the new non-donor build. The planned use is almost exclusively street cruising. The overall theme is a classic look and feel with completely modern mechanicals and premium driving. Because of the fully optioned anniversary edition, many aspects are already defined. Some of the specifics: Grey powder coat chassis, white powder coat on underhood panels and footboxes (intended to simulate the fiberglass of the originals), balance will be grey powder coat to match the chassis. 2015 Mustang IRS with 3.55 cast iron center section, FFR front spindles, front and rear sway bars, 13 inch front and rear Wilwood manual brakes, Wilwood pedal box with hydraulic clutch, engine driven power steering with 3.0 turn rack, upgraded Koni double-adjustable shocks, 18 inch FF Halibrand style wheels, new Coyote engine with footbox mods to maximize space, Stainless headers, GAS-N side pipes, TKO600 trans with Liberty’s shift mods, leather Roadster seats, Lizard Skin insulation, competition dash (tentatively) with glovebox, Speedhut gauges with GPS speedo, seat heaters, Breeze front battery, dropped floor in trunk, wipers, bumpers and overriders. Undecided about a heater. Haven't done one yet, and haven't missed it. But maybe it's time.

    That’s probably enough for now. I’m planning a number of the little mods and touches learned from the first two builds, and maybe some new ones along the way. Notably absent will be a sound system. Spent a lot of time on that with my last build, and find it not very practical. One of my goals is to have a really clean Coyote installation. Not easy with all the wires and hoses. I’ve seen some really great examples. I’ll see how I can do. Color is still undecided. I’m kind of stuck on red, and could easily do that again. But looking at some other options as well. It will have stripes. I’m going to take my time. This isn’t a race. Plus even though I’m retired and have more time than before, I also have other things going on. I’m expecting a roughly two year build, like the first two.

    There are 19 items on the backorder list. Many are minor, and won’t hold anything up. A couple others (front spindles, IRS parts) I’ll be watching closely. I’ve completed my inventory. I had a few missing and wrong parts. But not bad and I’m expecting will be quickly addressed. Probably my biggest observation, and I won’t say much at this point, is that I think I might be one of the first people to tackle the new 2015 Mustang IRS. I saw it in person at the Open House, and it’s really impressive and I think will make a great build. But it’s early for FF too. I’ll report more about it in the build thread as progress is made. I do already have the center section, knuckles and hubs on hand and ready to install. Talked about that in this thread: http://www.ffcars.com/forums/17-fact...so-begins.html.

    Going through everything, I'm generally pretty pleased. The windshield is now marked as made in Taiwan. The last two were from China. I wonder if they've changed vendors? It seems decent quality with everything nice and tight and clean. The new wheels are noticeably improved over the previous ones. The new tooling and new vendor has produced some nice parts. But those 18 inchers are huge! We'll see how that all turns out. The chassis looks good. The grey powder coating isn't real glossy, but it's nice. It seems they may have done some extra work prepping it before PC. I don't see much weld spatter. At least in many of the obvious places. Having a whole box of white PC'd panels before doing any fitting or drilling is different. I'll need to take care of those. The body looks good. All the panels match up OK at the parting lines. The new front quick jack mount brackets are interesting. I'll still do my usual grommet installation, but now even more to hold things up. I've got the newer style front UCA's. In general, interesting to see how they continue to make interim improvements to the same version. All good I think.

    In the true spirit of no pictures it didn't happen, here are a few of pics of the delivery process.

    From another forum member who saw my car in final assembly. Mine's on the RH side:



    On the rack and ready to go:



    Parking with the big dogs at a rest stop in New York on our way to Factory Five:



    Loading onto the frame cart:



    In she goes:



    Me looking a little sweaty, while my wife does her best Vanna White impression. Factory Five posted this pic on their Facebook page:

    Last edited by edwardb; 04-21-2020 at 08:51 PM.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
    Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.

  2. Thanks Mylo, Moniz thanked for this post
    Likes Aircontroller liked this post
  3. #2
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    10,547
    Post Thanks / Like

    EdwardB’s Mk4 #8674 20th Anniversary Build

    Safely back in Michigan, ready to roll back out:



    Yes, we used every inch:



    Home in the garage:



    Just a few boxes. All are in the basement now:





    Here's the new IRS chassis setup, before anything installed. I suspect many will be interested to see this:



    Here is a slideshow of all the pics taken during the delivery process, if you want to sit through them all: Delivery Slideshow by edwardb123 | Photobucket

    I’ll take the body off and start dis-assembly of the rest of the panels next week, in and around Woodward Dream Cruise activities. I’m going to store the body off-site this time around, rather than having it on an elevated buck like my last two builds. I won't miss the head bumping and sore back working under that thing. I’ll get the frame up on the 2-post and start plugging away. Stay tuned for much more!
    Last edited by edwardb; 08-08-2015 at 11:07 PM.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
    Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.

  4. #3
    Member BobCarter's Avatar
    Join Date
    Jun 2015
    Location
    Springfield, MO
    Posts
    98
    Post Thanks / Like
    Edwardb- WOW Congrats! Pics look great and the IRS shot with the FFR 5 laser cut out is a nice touch. With your experience and knowledge gained from 2 previous builds this one is sure to be another 1st place winner. I just heard from Stewart today about my delivery date. August 17th is my scheduled XMAS in August. Can't wait. Thanks for all the info you have shared in your posts and keep all of us up to date on your progress. #3 in the series will set the bar for the rest of us 20th Anniversary builders. ��

  5. #4
    Senior Member KDubU's Avatar
    Join Date
    May 2015
    Location
    Kennebunkport, ME
    Posts
    1,192
    Post Thanks / Like
    I notice you are using different boots on the LCA's and UCA's. The ones that come with the kit, dark blue, seem a bit liable to tear and I ordered some replacements from Summit but have not wanted to pull everything apart again to install. How do you find the ones with the kit and am curious why you have a few different ones?
    Kyle

    Complete Kit pickup 09/05/2015, 351w, QF680, 3.55, 3-Link, 15" Halibrands with MT's, Painted Viking blue with Wimbledon white stripes on 03/15/2017. Sold in 08/2018 and totally regret it.

  6. #5
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    10,547
    Post Thanks / Like
    Quote Originally Posted by KDubU View Post
    I notice you are using different boots on the LCA's and UCA's. The ones that come with the kit, dark blue, seem a bit liable to tear and I ordered some replacements from Summit but have not wanted to pull everything apart again to install. How do you find the ones with the kit and am curious why you have a few different ones?
    The LCA boots are unchanged as received with the kit. Those blue ones I left alone. They are crimped in place (or held on somehow) and seemed OK to me. I have similar ones on my completed Mk4 that's done and driving. They are holding up fine. For the UCA, I switched to Howe Racing ball joints as I described earlier in the thread. They don't come with boots, but that's OK because I really like the Energy Suspension boots. So for the UCA, those are the Energy Suspension 5.13102G boots. That part number contains both upper and lower. I just used the one pair. Less than $10 for all four. For the steering tie rod ends, those are Energy Suspension 9.13101G boots. About $7.00 for the pair. The boots supplied with the kit are maybe OK. But you can find lots of instances where they haven't lasted the life of the build. Maybe because the suspension is hanging at full droop for extended periods of time and they get distorted and crack? Whatever the reason, easy and cheap to put better ones in now. Much more work later. I found the best price for the boots on Amazon. If they have what you're looking for, their car part prices are usually pretty good.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
    Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.

  7. #6
    Senior Member
    Join Date
    May 2014
    Location
    Burlington, WI
    Posts
    689
    Post Thanks / Like
    Blog Entries
    1
    A question on ball joints as others may notice the same thing I do. The ball joints for the front LCAs, as mentioned, appear to be pressed into the control arm and the boots are secure. However, the left one's threaded shaft is impossible to rotate without the tap of a plastic mallet. The right side ball joint moves rather freely like a joystick. I applied synthetic grease to both but the left one shows no improvement. Should I be concerned? And if so, with which one?

    Has anyone else found this to be the case? BTW, I may have been one of the fortunate ones to have the upper ball joints go in easily.

  8. #7
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    10,547
    Post Thanks / Like
    Quote Originally Posted by ThickCobra View Post
    A question on ball joints as others may notice the same thing I do. The ball joints for the front LCAs, as mentioned, appear to be pressed into the control arm and the boots are secure. However, the left one's threaded shaft is impossible to rotate without the tap of a plastic mallet. The right side ball joint moves rather freely like a joystick. I applied synthetic grease to both but the left one shows no improvement. Should I be concerned? And if so, with which one?

    Has anyone else found this to be the case? BTW, I may have been one of the fortunate ones to have the upper ball joints go in easily.
    Both of my LCA ball joints were pretty tight. Probably similar to what you're describing for the one. For the one that moves freely, IMO unless there is any play at all, it's OK. You don't want the front suspension to bind, but it's stiff by design plus even more when it's brand new. During assembly, check that both UCA and LCA move OK individually after torquing down the bolts. They will be tight, LCA a bit more, but still should move with a little push. Then when you install the spindles, before you put in the coilovers, again check for free movement of the entire assembly. Everything will be stiff, but you should be able to get everything to move fairly easily. At that point, your ball joints are also moving. If it still doesn't seem right, then I would call FF. But I'm betting it's OK. Once you add the coilovers and sway bars (if you're using them) you can't really move the suspension by hand any more, so you can't tell anything at that point.

    Your experience with the upper ball joints is interesting. Many report trouble with this, and some like me just give up. Sure don't know where the variation is. As I documented, I couldn't get two different brands to go in. That would suggest the UCA's. But the Howe Racing parts went in smooth as could be. Strange.
    Last edited by edwardb; 12-06-2015 at 09:27 AM.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
    Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.

  9. #8
    Not a waxer Jeff Kleiner's Avatar
    Join Date
    Feb 2011
    Location
    Bloomington, Indiana
    Posts
    8,003
    Post Thanks / Like
    This will be fun to watch

    Jeff

  10. #9

    Join Date
    Jun 2015
    Location
    Parker, TX
    Posts
    286
    Post Thanks / Like
    I've been waiting for this post - I'm looking forward to following your build thread and the IRS updates!
    My production date is 8/22 so I'm not far behind.

    I've also got a question about what's included in the kit for the IRS (vent, bolts, bushings) but I'll ask it in your IRS thread to keep it all together.

  11. Likes mmklaxer liked this post
  12. #10
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    10,547
    Post Thanks / Like

    First Update

    The first week has mainly been ongoing preparations for the build. I've heard back from FF regarding my backorder list and several missing or wrong parts. Dan assured me all were taken care of. I also heard they have now received some (all?) of the 2015 Mustang IRS parts. So now the waiting begins for boxes to show up on my front porch. It will be a little while before I run out of things to do, but I'll be happy to see all that stuff arrive.

    Meanwhile, first order of business was to get the body off, onto a body buck, and stored out of the way for now. The last two builds I put together quite elaborate elevated body bucks, then ended up cutting them down and giving them to the painters thinking I would never need another body buck. Oh really? So this time I tried to keep it real simple. I have a frame cart (visible in some of the earlier pictures) so I thought why not use that as a removable base for the body buck? Overkill, but double duty would be a good thing. So I made a real simple frame on 24 inch centers to rest on the frame cart, and then just hung everything off of the frame. I used 7/16 inch ply instead of OSB because it's much lighter (plus I had a piece laying around). With the body buck done, used the SE to take the body over to our storage unit. I have it for our SE and also store the car there in the winter. There's enough height, so I hung the body/body buck in the back up against the ceiling. The SE still fits. Barely.

    One hint, while I'm thinking about it. There are a number of threads where guys are asking about their dash placement on the 3/4 inch dash hoop. Also about the clearance between the cockpit lip around the dash. I've been one of the advocates to actually temporarily place the body on the chassis during the build to get this all sorted out. With my body off-site, plus not the easiest to get up and down, I took the opportunity to check all that out while the body was still on from the initial delivery. I measured and made notes of exactly where the body is sitting in reference to the dash hoop. I also used a Sharpie and marked a line on the body lip 1/4 inch from the dash hoop. This gives me enough information to mount the dash with confidence, and also for the initial trim on the body during final assembly. I suspect the body will be in a slightly different position (mainly height) with all the aluminum and bulb seal in place, but this is still good enough to get me started.

    With the body up and out of the way, I got the frame up on the 2-post. This is my first build from the start with the 2-post. I'm going to like this! Now for some pics.

    Taking the body off for the first time, using my hi-tech ceiling hooks and pullies. What can I say? It works.



    Body buck frame using frame cart for wheels, when needed:



    Body buck all done:



    Hung from the ceiling at our storage unit. For peace of mind, as an afterthought I added some 2x4 braces to the floor. Almost for sure not needed, but will help me sleep at night. You can see what's left of the 2015 Mustang IRS pallet. Hope there's some Craigslist/eBay value there.



    Just fits: (SE needs a bath...)



    Now the fun begins:





    In the true spirit of all good projects deserve a little spilled blood, I had a bit of an incident yesterday. I was working hard and fast trying to get the buck done and then away for the evening at a Woodward Dream Cruise event. In the process, I was working inside the body with it on the buck. I stepped out going to the next thing and managed to catch my foot on the door sill. While trying to catch myself and thinking "Don't break the body…" I proceeded to face plant myself right onto the steel door sill of the frame sitting next to the body. A really hard hit and scared myself to say the least. I immediately went for the ice and surveyed the damage. Man was I lucky. Got myself in the cheekbone and gave myself a bloody nose. But no teeth, eyes, nose, whatever. This morning I woke up plenty sore and with a beautiful black eye. And no there won't be any pictures. Moral of the story, we all really need to be careful and go at the right pace and stop when we get tired. I was lucky this time.

    OK, enough of that. Next update will be installing the front suspension and steering rack. I don't have the spindles yet, so can't be a complete job. But I'll get started. First step will be installing the first pieces of aluminum, the F-panels. First sighting for those white powder coated pieces. I've got some white painted rivets and will try those.
    Last edited by edwardb; 08-14-2015 at 06:03 AM.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
    Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.

  13. #11
    Administrator David Hodgkins's Avatar
    Join Date
    Feb 2011
    Location
    Corona del Mar, CA
    Posts
    6,057
    Post Thanks / Like
    Blog Entries
    7
    Wow Paul I'm so jealous. I shoulda' pulled the trigger. It's a great kit loaded to the hilt and then some. I really like the new wheels with the milled outer radius. The special-edition gauges alone are a great add. And man, that IRS is STOUT. Wilwoods too? As part of the kit?? Sha-weet!

    A Coyote will be awesome and follow the prototype so there's a ton of factory support to count on. BTW Wookies love and support Coyote builds, though we can never have one of our own...

    Can't wait to watch you create/re-create those finishing touches that got you best overall at the Open House. Your last is your best and I can't wait to see what you come up with this time.


    FFR 5369 Pin Drive, IRS, Trigos, Torsen, Wilwoods, FMS BOSS 302 "B" cam , Mass-flo. CA SB100 (SPCN) Registered
    Delivered 4/23/06. "Finished" 4/2012 (still not done!)


  14. #12
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    10,547
    Post Thanks / Like
    Quote Originally Posted by David Hodgkins View Post
    Wow Paul I'm so jealous. I shoulda' pulled the trigger. It's a great kit loaded to the hilt and then some. I really like the new wheels with the milled outer radius. The special-edition gauges alone are a great add. And man, that IRS is STOUT. Wilwoods too? As part of the kit?? Sha-weet!

    A Coyote will be awesome and follow the prototype so there's a ton of factory support to count on. BTW Wookies love and support Coyote builds, though we can never have one of our own...

    Can't wait to watch you create/re-create those finishing touches that got you best overall at the Open House. Your last is your best and I can't wait to see what you come up with this time.

    Thanks for the kind words David! Yea, it's a sweet kit. I can't wait to see how it turns out either! But then I enjoy the process too much, so don't want to be in too big of a hurry.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
    Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.

  15. #13
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    10,547
    Post Thanks / Like

    Front Suspension

    Time for my first real assembly progress update. You guys asked for details, so you're going to get it.

    Over the last few days, I've completed the front suspension. At least as far as I can go without spindles. One of the items on my backorder list. First was the two F panels. These are part of the set of aluminum pieces powdercoated white as part of the Anniversary Edition. It's kind of a satin white. Not glossy. It's unusual is all I can say at this point. Will be interesting to see the total effect of all the engine compartment white PC. With the parts already coated but not test mounted, drilled, etc., it's a little different. I'm trying to handle them carefully, use tape, etc. to keep from marking them up. First order of business was to put a row of 10-32 nutserts in the back edge for the front splash guards. I've done this on my previous builds, and really like the serviceability. Another hint is to cut a 5/8 inch (or so) square from the top back corners. A similar cutout will be made in the front splash guards. This provides room for the convolute tubing and wiring along the outside edges of the hood surround. BTW, nice touch the PS didn't have the Mustang top radiator hose cutout, then requiring a fill panel. I used white silicone from HD and white rivets from McMaster. I tried to use a light touch with the pneumatic rivet gun, but the painted rivets still get marked up a bit. They look OK though. You can also see I put a bunch of painters tape on the exposed chassis powder coat in the area I'll be working for a while. Trying to keep from scratching up the PC, like I may have done on the last build. (!)



    Next I hung the lower control arms. Nothing much to say there. Once the PC was cleaned out of the holes, they bolted up fine. Note that I put a little red dot from a paint pen on all bolts that are tightened to the torque spec. Just a visual reminder to make sure I do them all. Once the build is done, the paint can be easily removed with a little lacquer thinner if needed. Then I put in the Breeze PS rack, the upper control arms with ball joints, and then the Koni shocks. The shock bolts are just finger tight for now. I figure I'll move them out of the way when it's time to bolt in the spindles.





    This is another pic of the Breeze PS rack. Nothing too earthshaking here. But a couple words. I used this same 3.0 turn Unisteer rack on my current Mk4, and for my purposes (mostly street driving) it's perfect. Since I bought and installed the last one, Mark at Breeze now provides them in PC black vs. silver, and also provides them with the rack extenders and extended boots already installed. Nice. He also includes a pair of limiters, in case you need them. I'll wait on those for now to see if I need them. I installed the rack with Mark's #70634 offset rack mounting kit, which I've used a couple times before. Centering for a Mk4 is not a big issue. This one was perfect, like my last Mk4. But the bushings, in addition to being solid vs. slightly flexible, move the rack slightly forward and slightly down. Forward is good because it helps the boots clear the chassis a little better. Down supposedly helps with bump steer, although with the newer geometry of the Mk4 and FF spindles, I'm not sure that's a big deal any more. Also in this pic you can see the -6AN adapters for the PS hoses. Those are from Maximum Motorsports.



    So I've had two issues so far. One was the upper ball joints. I received (like many) the Mevotech upper ball joints with my kit. And like many, they were too tight. No amount of freezing and heating did anything other than get a questioning look from my wife when I took the ball joints out of the freezer. I couldn't get more than 1-2 turns before they basically locked solid and I just wasn't going to crank on them like many have. I'm sure FF would have replaced them, but probably with more of the same. Like many, I decided to just spend the $17 each and change to Moog K772's. Well, we're having fun now. I received two very quickly from Amazon (best price) and one fit both sides perfectly, the other wouldn't even start threading. No amount of messing around changed anything. So I returned it and had a replacement a couple days later. Guess what? Same thing. Two out of three Moog parts wouldn't work. Note the one good one fit either UCA perfectly. The other two neither. OK, now I'm really frustrated. Read multiple forum posts, both ours and others, and found many guys are using Howe Racing ball joints. Yea, I know, now $60+ each. Budget? What budget? But how much is frustration worth? Received the Howe Racing 22320S ball joints this AM from Summit. Both fit perfectly. Used blue Loctite, and gave them a hefty tug while in the vise, same as shown in the manual. Then put a red paint mark that I'll keep an eye on. I'm confident they're not going anywhere though. In addition to being obviously high quality parts, they are serviceable and rebuildable.

    Last edited by edwardb; 12-06-2015 at 02:26 PM.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
    Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.

  16. Thanks NoBars thanked for this post
  17. #14
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    10,547
    Post Thanks / Like

    Front Suspension (continued)

    The second issue was with the Koni 2812 double-adjustable aluminum body coil-over shocks. The manual says to install the standard Koni front shocks body UP. But the Koni instructions for these shocks quite emphatically says they are to be installed body DOWN. Something about the special valving in this shock type only functions correctly when installed down. And Factory Five does have them installed body down in their 20th Anniversary Roadster. So that's what I did. But I then realized the body interfered slightly with the LCA. In fact, if you look closely at the pics FF has on their website of their 20th Anniversary Roadster, you can see divots in the shock body from the interference. I decided not to duplicate this feature. Using a cut-off wheel and then a small air belt sander, I removed the interference from the two sides and back and confirmed clearance with the shock at full extension and compression. It's not a lot, so I'm confident the strength of the LCA is not affected. Here are three pics. Before, after trimming, and then with the shock back in place. Before assembling, I touched up the bare metal with gloss black POR15, which matches the black PC perfectly.







    The outer tie rod ends supplied with the kit are absolutely fine, and will work perfectly. But I happen to like these Moog ES2150RL parts instead. In addition to maybe slightly higher quality, it's very likely not necessary to cut length off the inner tie rod. I used this same rack and these ends on my current Mk4, and no trimming was necessary. Also, because of the design, the threads are fully engaged and the excess goes into the pocket of the piece. No need to watch for the minimum one inch of thread engagement. I don't like changing out perfectly good parts. But these are nice and I chose them again.



    Finally, something a little interesting. The 20th Anniversary kit comes with front and rear sway bars. The rear setup is clearly pictured in the new IRS announcement. But I wasn't sure how the front would be done, since I don't have instructions that reference any of this yet. But what I did notice was an extension on the front chassis tube end with two holes. Different than my current Mk4 for sure. Guess what lines up into that extension and bolts there? I'm betting this:





    I wonder if these attachment points will be standard on all Mk4 kits now? If so, nice improvement for guys that want to add a sway bar and not have to do some of the mods I've seen. I received two of the pictured sway bars. They are .875 inch, from a company called Flyin Miata. For 90-93 Miatas. Is that allowed?? I have some of the pieces, but not all for where it attaches to the LCA. There are rod ends and then a bracket of some kind. More later!

    I'm still waiting for backordered parts (no shipments yet…) and especially some of the major missing IRS components. I've got plenty of other things to work on for now, so no panic. Yet.
    Last edited by edwardb; 08-18-2015 at 03:48 PM.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
    Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.

  18. #15
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    10,547
    Post Thanks / Like
    Quote Originally Posted by edwardb View Post


    I wonder if these attachment points will be standard on all Mk4 kits now? If so, nice improvement for guys that want to add a sway bar and not have to do some of the mods I've seen. I received two of the pictured sway bars. They are .875 inch, from a company called Flyin Miata. For 90-93 Miatas. Is that allowed?? I have some of the pieces, but not all for where it attaches to the LCA. There are rod ends and then a bracket of some kind. More later!
    Quick follow-up on these points since I received a copy of the instructions. According to the instructions, all kits made after April 2015 have the pictured sway bar attachments points on the front of the 4 inch chassis tubes. Brackets are available for kits made before that. The attachment to the underside of the LCA's is done with rod ends attached to a longer lower shock mounting bolt. Pretty straightforward.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
    Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.

  19. #16
    BadAsp427's Avatar
    Join Date
    Jul 2018
    Location
    Greeneville, TN
    Posts
    1,177
    Post Thanks / Like

    Very Important, Great Catch Paul!!!

    Quote Originally Posted by edwardb View Post
    The second issue was with the Koni 2812 double-adjustable aluminum body coil-over shocks. The manual says to install the standard Koni front shocks body UP. But the Koni instructions for these shocks quite emphatically says they are to be installed body DOWN. Something about the special valving in this shock type only functions correctly when installed down. And Factory Five does have them installed body down in their 20th Anniversary Roadster. So that's what I did. But I then realized the body interfered slightly with the LCA. In fact, if you look closely at the pics FF has on their website of their 20th Anniversary Roadster, you can see divots in the shock body from the interference. I decided not to duplicate this feature. Using a cut-off wheel and then a small air belt sander, I removed the interference from the two sides and back and confirmed clearance with the shock at full extension and compression. It's not a lot, so I'm confident the strength of the LCA is not affected. Here are three pics. Before, after trimming, and then with the shock back in place. Before assembling, I touched up the bare metal with gloss black POR15, which matches the black PC perfectly.






    AWESOME INFORMATION AND VERY IMPORTANT: Great Catch! So this could actually be a big deal... I just test fit my shocks and because of the binding that you indicate here, I only have about half of my upward travel and it is complete lock up and it can not go any further. Under loads, I'm positive this would/could cause major handling issues. I'm modifying my lower control arm shock mounts now.

    Mk4 20th Anniversary #8690 (#8 of 20) Purchased 8/18/18----Build Started 8/19/18
    Build Thread Click Here / Registry Entry Click Here / BluePrint Engines 347ci / TKO600
    Carb/Heater/Heated Seats/Cruise Control/Drop Trunk & Battery/Custom Cubby

  20. #17
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    10,547
    Post Thanks / Like
    Quote Originally Posted by BadAsp427 View Post
    AWESOME INFORMATION AND VERY IMPORTANT: Great Catch! So this could actually be a big deal... I just test fit my shocks and because of the binding that you indicate here, I only have about half of my upward travel and it is complete lock up and it can not go any further. Under loads, I'm positive this would/could cause major handling issues. I'm modifying my lower control arm shock mounts now.
    I don't know the exact timing, but at some point this was addressed by FFR and fixed. The LCA's on my Gen 3 Coupe build, delivered 8+ months ago with the exact dual action Koni's, don't interfere. The profile at the attachment points looks similar to this modification I did on the LCA's received with the 20th anniversary Roadster in 2015.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
    Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.

  21. #18
    Senior Member
    Join Date
    Oct 2021
    Location
    Sarasota, FL
    Posts
    260
    Post Thanks / Like
    EdwardB (Paul),

    I re-read your build threads repeatedly to ensure I get sanity from all the different opinions on building this car. What I noticed in your threads is no mention of trimming the UCA back side sleeves and threads like so many others do for the power steering setup. Is that just an omission on your part of the write up or you get sufficient play to get to the front alignment numbers Caster & Camber).

    Thanks

    Bill

  22. #19
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    10,547
    Post Thanks / Like
    Quote Originally Posted by maclonchas View Post
    EdwardB (Paul),

    I re-read your build threads repeatedly to ensure I get sanity from all the different opinions on building this car. What I noticed in your threads is no mention of trimming the UCA back side sleeves and threads like so many others do for the power steering setup. Is that just an omission on your part of the write up or you get sufficient play to get to the front alignment numbers Caster & Camber).

    Thanks

    Bill
    Trimming the UCA's isn't required 100% of the time. Sometimes it's possible to get the power steering caster setting without trimming. Some feel that it's easier to just trim during assembly and then it's not an issue. I chose to wait and see because IMO it's not that hard to take apart if necessary. In this case, I didn't have to.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
    Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.

  23. Thanks maclonchas thanked for this post
  24. #20
    Senior Member ehansen007's Avatar
    Join Date
    Mar 2011
    Location
    Aliso Viejo, CA
    Posts
    1,625
    Post Thanks / Like
    Wow! that is some setup! Very Jealous. Can't wait to see this one! Haven't seen that swaybar setup yet but it's very cool. Should help a ton. I want pictures of it cornering. For me I'm sticking with the period correct, classic wheelie stance which was popular at the time.

    64-Shelby-Cobra-num66_DV-12-MH-07.jpg

    Good luck and don't worry about the backorders, it's when you get your backorder and it's wrong! LOL. Seriously though I've had some serious discussions with the crew over there QC is their next big endeavor.

  25. #21
    Member BobCarter's Avatar
    Join Date
    Jun 2015
    Location
    Springfield, MO
    Posts
    98
    Post Thanks / Like
    Edwardb-
    The installation instructions for the IRS and Sway bar are now available. I am sending them to your email address.
    Best Regards BC

  26. #22
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    10,547
    Post Thanks / Like
    Quote Originally Posted by BobCarter View Post
    Edwardb-The installation instructions for the IRS and Sway bar are now available. I am sending them to your email address. Best Regards BC
    Bob -- Got 'em! Huge thanks.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
    Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.

  27. #23
    Carl carlewms's Avatar
    Join Date
    May 2012
    Location
    Nokesville, VA
    Posts
    1,125
    Post Thanks / Like
    I finally got around to reading the entire thread ... WOW is the word that best describes all of this beautiful work.

    With respect to the installation of the Breeze solid bushings ... Did you have grind off any part of the mounts mentioned in his instructions?

    Again thanks for the detail you provide us guys building our first one of these.
    Mk 4 Roadster
    October 25, 2012 - Kit Arrives
    April 8, 2013 - Build Starts
    August 23, 2015 - Rolling Chassis/Engine & Transmission Installed
    March 26, 2016 - Go Cart

  28. #24
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    10,547
    Post Thanks / Like
    Quote Originally Posted by carlewms View Post
    I finally got around to reading the entire thread ... WOW is the word that best describes all of this beautiful work.

    With respect to the installation of the Breeze solid bushings ... Did you have grind off any part of the mounts mentioned in his instructions?

    Again thanks for the detail you provide us guys building our first one of these.
    You're certainly welcome. Fun to share, and always happy to hear it's appreciated. For the Breeze bushings -- no, didn't have to do any trimming as described in the instructions. Didn't have to trim anything on the previous Mk4 either. I guess things have changed since those were written.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
    Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.

  29. #25
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    10,547
    Post Thanks / Like

    IRS Update

    This past week I received a copy of the IRS instructions (thanks Bob!) plus my first backorder shipment. Still a ways to go, but progress. I now have the first of the three control arms. I already had most of the hardware. But things are starting to take shape a little now. First a recap briefly mentioned in the opening post. The 2015 Mustang IRS setup requires three parts from a 2015 Mustang: The center section (differential), knuckles, and hubs. The rest of the parts are supplied by FF as part of the new IRS setup. You don't need the donor CV joints and have to install them onto new axles as in some earlier versions. FF is supplying the CV axles completed and ready to assemble into the suspension, e.g. with joints, boots, etc. Not long after ordering the kit, FF suggested I may want to start looking for the donor parts. I found complete 2015 Mustang rear suspension pallets at MPS Auto Salvage in Georgia, and picked one up. It's a "zero miles take-off" meaning the newly assembled Mustang went from the factory in Flat Rock, MI to an aftermarket performance assembly line and part of their upgrade is to replace the entire rear IRS assembly. The new IRS setup is beefy, but apparently not up to the task of the 800-900 HP aftermarket engine mods, stickier tires, etc. Although I only need a few parts off the pallet, at the time MPS wasn't selling them separately. Some other places were, but the cost for the individual pieces was higher. So, received the pallet looking like this:



    Removed the parts I needed. I'm hoping to sell the balance and recover some of the cost. In total, should be a pretty good deal. The 3.55 center section case is cast iron, and posi like all new Mustang diffs.



    The cast iron center section had some surface rust. Not unexpected. The hubs too had a little surface rust. But the parts appeared to be exactly as advertised. Basically brand new parts. A little wire wheel action and the rust was removed off the cast iron. After thorough cleaning and degreasing, applied some POR15 to the iron and clear Dupli-Color engine spray to the rear aluminum cover. Now ready for installation.



    The knuckles require a piece of one of the arms to be cut off. I saw this in the pictures and write-up, but waited until the instructions were in hand giving the details. The instructions give the location and shows using a Sawzall. I don't own one, plus prefer a little more "civilized" approach. With some blocks clamped to hold the knuckles square, I cut them with a band saw. Took it slow and easy and worked fine. A little scary though, lopping off those pieces.



    Cleaned up the cut using a disk sander, and then filed and sanded a little radius. I went over the complete knuckles and knocked off some of the larger casting parting lines and just cleaned up in general, and then gave them a quick coat of clear Duplic-Color like the center section. Not required at all, but I've had good luck with this stuff and should stay looking clean and nice for a while. I think they're good to go.



    The standard Mustang wheel wheel studs need to be changed to 1/2 x 20, same as the supplied front hubs and matching the lug nuts provided with the FF wheels. The 10 new wheel studs are included with the kit. The instructions show hitting the old ones out with a hammer. I chose instead to use a short piece of black pipe and squeeze them out using my bench vise. Took some muscle, but worked OK. The instructions showed putting the new ones back in with a lug nut, washer and a ratchet. I'm apparently not strong enough because that didn't work for me. Mainly I think because it's impossible to hold the hub while putting that much torque on it. So I rummaged through my junk hardware drawer and found a hardened 1/2 x 20 nut and few hardened washers. Lubed them up good with some assembly lube, and pulled all the studs in with an air impact driver. A press would be ideal to remove and replace the wheel studs, and thought maybe I had an excuse to finally buy one. But no luck. Managed without it. Then cleaned up the exposed parts of the hubs and also applied some POR15 and put them back in the knuckles. Note this is one of many changes with the new IRS parts. The axle bearing is in a bolted in carrier. No longer necessary to press the axle bearings in and out of the aluminum knuckle itself. Also note the little cover and screw in the knuckle just above the hub. This is where the standard ABS sensor is normally mounted. I'm not going to try an ABS installation, so don't need the sensor. But didn't want to leave an open hole directly down into the axle bearings. So made a little cover out of 1/8 inch aluminum and used the sensor mounting screw to hold it in place.

    Last edited by edwardb; 05-31-2016 at 05:57 AM.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
    Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.

  30. #26
    Mark Eaton's Avatar
    Join Date
    Apr 2017
    Location
    Medford, Oregon
    Posts
    752
    Post Thanks / Like
    Quote Originally Posted by edwardb View Post
    This past week I received a copy of the IRS instructions (thanks Bob!) plus my first backorder shipment. Still a ways to go, but progress. I now have the first of the three control arms. I already had most of the hardware. But things are starting to take shape a little now. First a recap briefly mentioned in the opening post. The 2015 Mustang IRS setup requires three parts from a 2015 Mustang: The center section (differential), knuckles, and hubs. The rest of the parts are supplied by FF as part of the new IRS setup. You don't need the donor CV joints and have to install them onto new axles as in some earlier versions. FF is supplying the CV axles completed and ready to assemble into the suspension, e.g. with joints, boots, etc. Not long after ordering the kit, FF suggested I may want to start looking for the donor parts. I found complete 2015 Mustang rear suspension pallets at MPS Auto Salvage in Georgia, and picked one up. It's a "zero miles take-off" meaning the newly assembled Mustang went from the factory in Flat Rock, MI to an aftermarket performance assembly line and part of their upgrade is to replace the entire rear IRS assembly. The new IRS setup is beefy, but apparently not up to the task of the 800-900 HP aftermarket engine mods, stickier tires, etc. Although I only need a few parts off the pallet, at the time MPS wasn't selling them separately. Some other places were, but the cost for the individual pieces was higher. So, received the pallet looking like this:



    Removed the parts I needed. I'm hoping to sell the balance and recover some of the cost. In total, should be a pretty good deal. The 3.55 center section case is cast iron, and posi like all new Mustang diffs.



    The cast iron center section had some surface rust. Not unexpected. The hubs too had a little surface rust. But the parts appeared to be exactly as advertised. Basically brand new parts. A little wire wheel action and the rust was removed off the cast iron. After thorough cleaning and degreasing, applied some POR15 to the iron and clear Dupli-Color engine spray to the rear aluminum cover. Now ready for installation.



    The knuckles require a piece of one of the arms to be cut off. I saw this in the pictures and write-up, but waited until the instructions were in hand giving the details. The instructions give the location and shows using a Sawzall. I don't own one, plus prefer a little more "civilized" approach. With some blocks clamped to hold the knuckles square, I cut them with a band saw. Took it slow and easy and worked fine. A little scary though, lopping off those pieces.



    Cleaned up the cut using a disk sander, and then filed and sanded a little radius. I went over the complete knuckles and knocked off some of the larger casting parting lines and just cleaned up in general, and then gave them a quick coat of clear Duplic-Color like the center section. Not required at all, but I've had good luck with this stuff and should stay looking clean and nice for a while. I think they're good to go.



    The standard Mustang wheel wheel studs need to be changed to 1/2 x 20, same as the supplied front hubs and matching the lug nuts provided with the FF wheels. The 10 new wheel studs are included with the kit. The instructions show hitting the old ones out with a hammer. I chose instead to use a short piece of black pipe and squeeze them out using my bench vise. Took some muscle, but worked OK. The instructions showed putting the new ones back in with a lug nut, washer and a ratchet. I'm apparently not strong enough because that didn't work for me. Mainly I think because it's impossible to hold the hub while putting that much torque on it. So I rummaged through my junk hardware drawer and found a hardened 1/2 x 20 nut and few hardened washers. Lubed them up good with some assembly lube, and pulled all the studs in with an air impact driver. A press would be ideal to remove and replace the wheel studs, and thought maybe I had an excuse to finally buy one. But no luck. Managed without it. Then cleaned up the exposed parts of the hubs and also applied some POR15 and put them back in the knuckles. Note this is one of many changes with the new IRS parts. The axle bearing is in a bolted in carrier. No longer necessary to press the axle bearings in and out of the aluminum knuckle itself. Also note the little cover and screw in the knuckle just above the hub. This is where the standard ABS sensor is normally mounted. I'm not going to try an ABS installation, so don't need the sensor. But didn't want to leave an open hole directly down into the axle bearings. So made a little cover out of 1/8 inch aluminum and used the sensor mounting screw to hold it in place.

    I have two questions about painting the rear differential. #1) Did you use the full prep with POR engine degreaser and metal prep before applying the POR 15 paint? and #2) What is the purpose of the clear coat of Dupli color paint? Does it protect the aluminum somehow or just make it look better for car shows?

    Thanks so much

    Mark

  31. #27
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    10,547
    Post Thanks / Like
    Quote Originally Posted by Mark Eaton View Post
    I have two questions about painting the rear differential. #1) Did you use the full prep with POR engine degreaser and metal prep before applying the POR 15 paint? and #2) What is the purpose of the clear coat of Dupli color paint? Does it protect the aluminum somehow or just make it look better for car shows?

    Thanks so much

    Mark
    Yes to the first part. I use the POR degreaser and metal prep products before applying POR-15. For the second question, I like to use the Duplicolor clear on aluminum parts like the center section cover, knuckles, etc. when they're new and clean. Then they stay that way. Dirt and grime wipes right off. I wouldn't say it's for car shows or visual in any way because 99% of the time the parts aren't visible with the car on the ground. But I've been known to put the car on the lift and clean the underside. Call it anal, call it whatever. It's not for everyone and I'm not promoting it. Just something I like to do.
    Last edited by edwardb; 09-17-2017 at 08:17 PM.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
    Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.

  32. #28
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    10,547
    Post Thanks / Like

    IRS Update (continued)

    So in yesterday's shipment, I received the IRS toe arms. That with the hardware already received this is starting to shape up. Here is the PS knuckle with the toe arm attached at the bottom, and the hardware for the upper control arm temporarily attached to the now trimmed arm.



    Here is the complete toe arm. Note how the setup will allow adjustments without disassembly. For the toe arm and upper control arm. Nice. The lower control arm is fixed BTW.



    Last shot of the PS knuckle, showing all three attachment points. The lower control arm attaches to the shorter leg, which is also the same location the coilover attaches. Someone asked in my previous thread about the IRS whether the Ford installed bushings in the two lower arms would be used. Apparently the answer is yes. No new parts received and no instructions to remove existing. Good thing, because they look pretty solidly installed. The upper control arm location is bolted in as shown, with the provided rod end. Nothing to remove or add there either.



    Hopefully the next pics will be with all this installed, once I receive the arms and the last pieces of hardware. Meanwhile, still plenty to work on. Work is underway on the Wilwood pedal box, and yes, we still have the famous clutch arm frame interference. Will probably do the same mod as the previous Mk4.
    Last edited by edwardb; 08-23-2015 at 11:22 AM.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
    Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.

  33. #29

    Join Date
    Jun 2015
    Location
    Parker, TX
    Posts
    286
    Post Thanks / Like
    VERY impressive - This is extremely helpful information and very much appreciated!
    Thank you for sharing!!

    What did you use for the general cleanup of the aluminum knuckles?
    Last edited by RRussellTx; 08-23-2015 at 12:31 PM.

  34. #30
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    10,547
    Post Thanks / Like
    Quote Originally Posted by RRussellTx View Post
    VERY impressive - This is extremely helpful information and very much appreciated!
    Thank you for sharing!!

    What did you use for the general cleanup of the aluminum knuckles?
    Thanks and you're welcome. Some files to knock off the parting lines, then just a couple different light wire wheels in a hand drill, some emery cloth, and then some Scotch-Brite pads. I've seen some really nice results guys have done on the previous style knuckles with media or bead blasting and even clear powder coat. But I kept it simple with stuff I had around the house. Nothing very fancy and certainly optional.
    Last edited by edwardb; 08-23-2015 at 01:20 PM.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
    Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.

  35. #31

    Join Date
    Mar 2014
    Location
    Louisville, KY
    Posts
    29
    Post Thanks / Like
    Love seeing the progress your making on your build.
    I just picked up my kit last weekend. I also picked up the IRS center and spindles from FF while I was there, saved the shipping costs. FF is starting to supply them also. I have not seen them in the parts catalog yet, but if you ask, you can get.
    the IRS center I received is also aluminum, not cast iron. I know the IRS manual says to use the cast unit only but they assured me it was just because the flange adapter hadn't been designed at the time.
    Build 1: MkIV Roadster #8675. Deliv: 8/15/2015.
    FFR MkIV complete kit. / 5.0 Coyote Motor / T56 Magnum Trans / 2015 IRS / 18' Halibrand w/Michelin Pilot Sport PS2 Tires
    FFMetal: Firewall Forward, Trans Tunnel top, Battery Box, Fan Shroud
    Russ Thompson: Turn signal Assembly, Trunk Box Mod.
    Breeze: SS Roll Bars(2), Power Steering rack, and much more.
    Mike Forte: supplied 5.0 Coyote & T56 Magnum Trans

  36. #32
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    10,547
    Post Thanks / Like
    Quote Originally Posted by wirelessnut View Post
    Love seeing the progress your making on your build. I just picked up my kit last weekend. I also picked up the IRS center and spindles from FF while I was there, saved the shipping costs. FF is starting to supply them also. I have not seen them in the parts catalog yet, but if you ask, you can get. The IRS center I received is also aluminum, not cast iron. I know the IRS manual says to use the cast unit only but they assured me it was just because the flange adapter hadn't been designed at the time.
    Congratulations on your new kit! #8675, next in line after mine. Also a 20th Anniversary Edition? Yea I knew FF is offering the IRS parts. They offered me a set as well, but happened after I had shopped around and found them on my own. They actually bought out the supply of the zero mile take-offs from the same place I got mine. I wonder if that's what they're still offering? I also knew they said a aluminum center was OK, and I would have taken it if available, but the only 3.55 available at the time was the cast iron version. They are definitely stronger, which is why Ford is only putting aluminum in automatic Mustangs, and cast iron in sticks. But for our purposes, given the much lighter weight, I'm sure the aluminum is still way plenty strong enough. Other than the 20 pounds or so of extra weight (much like me, but let's not go there...) I'm not sure there's any downside to the cast iron case other than a little extra heft to lift into place. Keep us posted on your build!
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
    Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.

  37. #33

    Join Date
    Mar 2014
    Location
    Louisville, KY
    Posts
    29
    Post Thanks / Like
    Quote Originally Posted by edwardb View Post
    Congratulations on your new kit! #8675, next in line after mine. Also a 20th Anniversary Edition? Yea I knew FF is offering the IRS parts. They offered me a set as well, but happened after I had shopped around and found them on my own. They actually bought out the supply of the zero mile take-offs from the same place I got mine. I wonder if that's what they're still offering? I also knew they said a aluminum center was OK, and I would have taken it if available, but the only 3.55 available at the time was the cast iron version. They are definitely stronger, which is why Ford is only putting aluminum in automatic Mustangs, and cast iron in sticks. But for our purposes, given the much lighter weight, I'm sure the aluminum is still way plenty strong enough. Other than the 20 pounds or so of extra weight (much like me, but let's not go there...) I'm not sure there's any downside to the cast iron case other than a little extra heft to lift into place. Keep us posted on your build!
    No, I didn't get the Anniversary Edition. As much as I would have liked, the budget just wouldn't allow it. If all goes well with this build (as it should), I'll be eyeing a 25th Edition.
    I had already been picking up parts for the build when FF started the 20 days of specials. Saved a bunch on the 50/50 deals. Glad I waited for the new IRS, but now I have and older version Aluminum IRS I'll need to sell. I did the same as you and picked up the kit at FF. Made a road trip of it with my 18Yr. old son and 21Yr. old daughter.
    I'm still doing inventory on my kit. I have a bunch of work to do on the garage to prep it for the build. I'll post some pics as soon as there is progress.
    Build 1: MkIV Roadster #8675. Deliv: 8/15/2015.
    FFR MkIV complete kit. / 5.0 Coyote Motor / T56 Magnum Trans / 2015 IRS / 18' Halibrand w/Michelin Pilot Sport PS2 Tires
    FFMetal: Firewall Forward, Trans Tunnel top, Battery Box, Fan Shroud
    Russ Thompson: Turn signal Assembly, Trunk Box Mod.
    Breeze: SS Roll Bars(2), Power Steering rack, and much more.
    Mike Forte: supplied 5.0 Coyote & T56 Magnum Trans

  38. #34
    Senior Member
    Join Date
    May 2014
    Location
    Burlington, WI
    Posts
    689
    Post Thanks / Like
    Blog Entries
    1
    Edwardb,

    Fantastic build thread. And, it's very timely for me as I am anxiuously awaiting delivery of my Anniversary addition (and first build) this coming week. For a few years now, I've thought of building the Cobra. I have followed the forums and recently committed to diving in by starting with the build school a few months back. I have reached out to a few individuals and think I now have most of my ducks in a row. And, now with your build thread...I'm ready to go. And, I had a garage to finish to "make things happen".

    Keep us updated on your progress. It's much appreciated.

  39. Likes Fman liked this post
  40. #35
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    10,547
    Post Thanks / Like

    More Progress plus Center Section Installed

    It's been an eventful week wrapping up several smaller details that I had started. I've received two boxes of backordered/missing parts, with two more due here tomorrow. This list is getting shorter, but I'm still missing the upper and lower IRS control arms and the CV axles. So I'm unable to make much progress with the highly anticipated new IRS. But then I decided why not install the center section in the frame? Now that would be progress. The good news is that it's installed and looking good. But it was somewhat challenging. I'll describe more, but first some smaller stuff.

    I cleaned and painted the pedal box mounts, assembled them to the Wilwood pedal box, and checked the fit in the DS footbox. As mentioned in my last update, immediately noted that the clutch arm interference with the 3/4 inch chassis tube that crosses in that area remains an issue. This subject has been discussed and debated at length, including the background, various options to fix, etc. I'm not going to repeat all that here. Multiple threads on the topics. I decided to do the same frame mod that was done on #7750, which is similar to the frame mod Whitby does for their power brake kit. Cut out the interference, then make a plug for each end of the opening, and bridge with another bolted on piece. This approach has also been done by others, and IMO works very well and easily is as strong as the unmodified frame. I used an air saw to remove the roughly two inch section where the interference occurs. Then used some 5/8 inch square mild steel to make the plugs, and some 3/4 inch square mild steel to make the bridge piece. Aluminum would probably be just fine, but I was duplicating what worked well before. Here are the final pieces ready to install alongside the piece that was removed. I made the plugs as long as they could be to still fit into the opening and push into the ends. The front piece had to be trimmed a bit to clear some weld that penetrated the tube in that area.



    I sprayed some paint on the parts that showed. After a couple attempts, found some rattle can paint that matches the 20th Anniversary powder coat reasonably well: Rust-Oleum High Performance Wheel Paint, color 248930 GRAPHITE. It was in the automotive section of our local HD. The piece here doesn't show once the build is done, but still didn't want to leave it bare and wanted to find something that matched pretty close in case I needed it elsewhere during the build. Here are the parts installed. I buttered the plugs with JB Weld before pushing in and bolting it up. Rock solid.



    Just to give an idea of the interference, tried to get a couple pictures. Not too easy to show very well because of the angles. This is the clutch pedal all the way to the back wall, from the side and the top. I found that if I want the clutch pedal to be even with the brake pedal (important to me) and use the standard Forte hydraulic setup, this is the amount of travel that it needs. Maybe it's just my memory (very possible) but this actually seems like more interference than my previous Mk4. Some guys have decided to notch the clutch arm to clear. Not my choice (again not debating here) and especially since it would go nearly halfway through the arm in this case. Not sure if something has changed or not. Whatever, problem solved for this build.





    So, moving on, installed the master cylinders on the pedal box. FF now supplies 3/4 inch for the front, and 5/8 inch for the back. Doesn't say which side to put them on. I don't think it matters though, as long as it's plumbed properly. I chose the front toward the center of the car. I was a little interested that this is the first time I've seen these MC's without Wilwood cast into the side. Something generic, not Wilwood? Or did Wilwood just change them? Oh well. As mentioned, I'm going to be installing a hydraulic clutch setup, which I don't have yet. So nothing installed on the clutch side yet.



    One small detail on the bottom of the footbox. FF provides a small bracket and a switch for the brake lights, which I installed per the instructions. The Ron Francis harness also includes a clutch interlock, meaning the clutch pedal needs to be down for the engine to start. I want this feature, so like on my last build, made a clone of the provided FF bracket from 1/8 inch steel and bolted it in the proper position on the clutch side. I don't have the switch yet. Not the best picture (sorry for the focus) but you get the idea. Upon further review, seems there might be something in the Coyote setup and wiring to also provide the no start function. We'll see if this gets used.



    I temporarily installed the steering column. I haven't completely decided what's happening with the footbox sheet metal. Will likely be the King modified panels, so until I get that worked out and mocked up, not attaching the footbox front yet. I found it was necessary to install the footbox front steering column bearing on the inside. Not a big deal, since this is a common change when space is at a premium on the front of the footbox. But in this case seems the output shaft from the Breeze supplied Unisteer PS rack is slightly longer than usual. The adapter is all the way on, but still a few splines are showing. End result is the shaft wouldn't plug onto the adapter with the bearing on the outside of the footbox. So moved it inside and all is good. What I wanted to show though was I found in my last two builds that sometimes it's nearly impossible to get all the play out of the collapsing steering column. Even with the supplied Belleville washers properly installed. The slightest amount of play is noticeable and undesirable, especially in these cars. Some guys wedge shims up between the column pieces. I tried that before and didn't like it too much. What I've ended up doing is to install two 8-32 set screws in each side of the column. Once everything is assembled, I use a little red Loctite and just lightly tighten them against the inner column. Removes any remaining play, and doesn't defeat the collapsing capability. A little hard to see, but here's where I installed them:

    Last edited by edwardb; 09-20-2015 at 06:59 AM.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
    Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.

  41. #36
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    10,547
    Post Thanks / Like

    More Progress plus Center Section Installed (continued)

    Finally, before moving onto the main event, I installed couplers for the rear bumpers. Now is the time before any sheet metal or tank mounting. For new builders, the stock setup, especially now with the Mk4 where everything back there is really tight, the tank must be dropped to install/remove the rear bumpers or quick jacks, whatever you install. With the couplers, no longer necessary to drop the tank. I happen to like 7/16-20, because that's the threaded rod and hardware I use. Any similar size is good. Just one very small hint though. Pay attention to where you bolt these down. The holes in the frame are pretty large. Measure the vertical and horizontal locations, compared to the holes in the body and the bumper if you're going to use one. If you stack all the tolerances one direction, it's possible to be off 1/8 inch (or more) and complicates final assembly when that time comes. Ask me how I know…



    Ok, so finally to the center section installation. The Factory Five instructions show this installation needing a friend. Well, I have friends (really!) but most not available during my leisure retirement hours or in the immediate area. I'm mainly a solo act. So in this case my friend was the trusty shop crane. Obviously this is the only time this method would be usable. Once all the sheet metal is in place, it's would be all hands on deck working from the bottom. You have to tip it a lot to get it into place, so at first I messed around a bit with my engine leveler. That was overkill, and I ended up just using the same ratcheting pulleys I use to raise and lower the body adjusting each as I went. At 90+ pounds this thing gets your attention, but it's manageable. The pictures pretty much tell the story.











    Last edited by edwardb; 08-28-2015 at 08:16 PM.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
    Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.

  42. Likes facultyofmusic liked this post
  43. #37
    Member BobCarter's Avatar
    Join Date
    Jun 2015
    Location
    Springfield, MO
    Posts
    98
    Post Thanks / Like
    EdwardP- may I ask, what is the white material visible inside the coupler? Looks a bit like white Grease...
    Also, did you reinstall the body shell to check alignment of couplers to body holes? Reason I ask is there appears to be traces of red on the coupler ends. I kinda doubt you went to all the trouble of reinstalling the shell but I'm curious what could have left a red trace in some areas of the coupler end.
    NICE work on your solo install of the center section. I have been developing a strategy for my solo install too. I do not have a shop hoist so I will probably use my John Deere (6000 series). A bit over-kill but when you are working alone sometimes one needs all the muscle they can find! Great improvisation on the alignment pins as well. I can tell you are a guy who takes on a challenge with creativity and lots of ceiling study at night.

  44. #38
    Member BobCarter's Avatar
    Join Date
    Jun 2015
    Location
    Springfield, MO
    Posts
    98
    Post Thanks / Like
    Sorry, should have addressed the previous posts to Edwardb not Edwardp. Oops

  45. #39
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    10,547
    Post Thanks / Like
    Quote Originally Posted by BobCarter View Post
    What is the white material visible inside the coupler? Looks a bit like white Grease... Also, did you reinstall the body shell to check alignment of couplers to body holes? Reason I ask is there appears to be traces of red on the coupler ends. I kinda doubt you went to all the trouble of reinstalling the shell but I'm curious what could have left a red trace in some areas of the coupler end.
    Nothing going on with the couplers. Just plain threads inside and no red on the outside. Probably just reflections or from the flash. I use an external flash for fill on most shots. No, I didn't install the body shell. It's still comfortably hanging over at the storage unit. I did confirm the measurements though. The holes are exactly 31 inches apart horizontally, and 2-1/4 inches apart vertically. I mounted the couplers with the same spacing. I didn't pay attention to this on the last build, and had to enlarge the holes in the body quite a bit during final assembly. Not a big deal, but just trying to avoid this time around.

    Quote Originally Posted by BobCarter View Post
    The challenge I face is preserving the expensive POR 15 from one painting session till the next. I have used plastic wrap to help reseal the open container, used cheap chip brushes which I discard afer each use etc. but after following your build thread and seeing how many items you coat with the stuff I was wondering what your method is for maintaining a fresh (unskinned surface) POR product? Its great stuff but difficult to keep fresh.
    I'm still working out of the same pint can of gloss black POR15 I bought to touch up the DART block on my last build. Probably about two years ago, at least? I guess I've been lucky. I make sure the can seal is as clean as possible, lid on tight, then wrap in a plastic bag with a rubber band. Nothing really special. It stays in my pretty cool basement most of the time. Maybe that helps too.
    Last edited by edwardb; 08-29-2015 at 07:46 PM.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
    Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.

  46. #40
    Jacob's Avatar
    Join Date
    Jun 2016
    Location
    Rogers, AR
    Posts
    322
    Post Thanks / Like
    Do you recall what the length of your couplers are? Is the length critical? Looks like an easy way to avoid dropping the gas tank! thanks in advance.
    MK IV complete Kit - 1st time builder started Sept 2016
    Levy 306
    T5
    2015 Mustang IRS
    Power steering - Levy setup, Breeze roll bars, Thompson trunk box
    fuel injection, powder coating, sway bars, heater, wipers, 17 in wheels

Page 1 of 17 12311 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Martin's Dent and Collision Shop

Visit our community sponsor