-
Back at it, interior time..
Was too busy to work on my gtm for about a year now, but I finally got it back to my shop and am going to make a big effort to finish it this year. I don't have too much left, but a good amount. The biggest issue is the interior at the moment. All the panels are peeling, and they really don't fit the overall vibe of the car. I was going to go wild and fab up a complete interior, but I have dialed it back a bit and am going to just work with with they have provided, add some flair to the gauges, and make a nice center console to house an Alpine Halo9 radio and the heater/ac controls. So far, I have just about finished the gauges. Heres what I got.
Made some 3D bezels for the gauges to try and give the cluster some depth/layers. Looking at most modern cars that come in my shop, theres a nice big screen in between a couple analog gauges. I chose the AEM CD5 5" gauge pack to fit between the tach and speedo supplied by FFR. The CD5 will show me every gauge too, as well as G-forces, tilt, yaw, etc. Its a very cool piece that is nearly 100% customizable.
-
Nicely done, just saw your post on my thread. I love the capability of the AEM dashes. I've also got the vehicle dynamics module. I found a nice area right in the center tunnel to mount it. Its only about 1.5 inches off of vehicle center line front to rear.
-
Post Thanks / Like - 0 Thanks, 1 Likes
-
-
Very nice work! Those gauge bezels look like they would have been a bear to make on an angle like that? Looks great!
Shane Vacek
VRaptor SpeedWorks, LLC
www.vraptorspeedworks.com
Turn-key GTM, SL-C & Ultima GTR Built to Your Specs!
Offering a full line of GTM Upgrades and Custom Parts
-
Senior Member
Looks like you are off to a great start, can't wait to see the finished dash! Is that a stitched leather dash cover?
MK3.1 2004 Mach 1 donor. ABS, PS, TC.
GTM #304 LPE 525hp LS3
2000 C5 Lingenfelter LS1@489hp
1999 Corvette FRC/Z06 track car
-
Thank you. They aren't too bad Shane, just make a jig and run it on the router table. like an upside down mill lol
beeman, thats the crap that someone at factory five attempted to glue down 8 years ago. I have been cutting it away from the spots I have been working on so I don't have to deal with all the glue yet.
-
Not much to update, but I made the finalized bezel out of acrylic. The bezel is now 1 piece from the radio to the shifter. Made out of 1/4" acrylic, bent to fit the dash. Took me 3 tries. First one didn't bend well, second broke when I bent too far and tried to reverse a little, third times a charm. I am going to paint the back side of it and it will give a really deep finish. Next up I am going total care of mounting all the pieces into the car and to each other, then work on an armrest. After that, door panels...
-
Senior Member
Very nice!
How are you mounting the tablet? I'm getting started on my dash too...
MK3.1 2004 Mach 1 donor. ABS, PS, TC.
GTM #304 LPE 525hp LS3
2000 C5 Lingenfelter LS1@489hp
1999 Corvette FRC/Z06 track car
-
Lots of toys in this car!
A small suggestion:
You may want to try a slim rectangular air vent and drop your tablet down a few inches for extra front view clearance.
Custom LCD Gauges , Data Loggers, Control Touch Screens
www.LCDdash.com \\ 647-522-9953 \\ Voice & Text
Proud new owner of GTM Gen 1., #105 - 08/27/11
LQ9 Powered, G96.00 6 speed transaxle