-
SS383 Build - 33 Hot Rod #1134
Ready to start the adventure.
- 33 Hot Rod 2nd Gen
- Full fenders and top
- A/C P/S P/W
- 383 Chevy w/ Tremec 5sp
- Moser 3 Link
- Wilwood Brakes all around
- Other fun stuff to be determined.
Garage all ready
IMG_1080.jpg
Delivery Time from the big Red Truck (thanks Jim)
IMG_1097.jpg
Ready for Inventory
IMG_1102.jpg
Last edited by peterh226; 04-15-2019 at 07:43 PM.
- Peterh226 #1134
'33 Hot Rod 2nd Gen. Blueprint 383 Sniper TKO Delivered 4/14/2019
Full Fenders, Top, 3-Link, Wilwoods
YOKOHAMA ADVAN NEOVA AD08 R | Fr 245/45 R17 | Rr 295/30 R18
AR605 Torq-Thrust M Chrome | Fr 17x8 | Rr 18x10
-
Post Thanks / Like - 0 Thanks, 1 Likes
-
Seasoned Citizen
Good choice for power. Have fun.
Dart Little M 406" SBC 800 HP N/A & 1,100 HP on nitrous, 2-spd Powerglide with trans brake, 6,000 RPM stall converter, narrowed Moser 88 3.90:1 spool with 35-spline gun-drilled axles & Torino bearings, custom parallel four-link, custom tube chassis & roll cage NHRA certified for 8.5-sec (only two FFR Hot Rods have this cert).
33 Hot Rod Super Pro Drag Racer Build:
33 HR NHRA Cert Roll Cage Build
-
Senior Member
33' Hot Rod Coupe/Roadster (GEN 1), Fendered, Ford 302, 350hp, EFI, AOD, 4-Link, Double Adjustable Koni Coilovers, Split Rear Exhaust, Electric Power Steering, AC/Heat/Defrost, Moser 8.8"-3.55, Willwood Front/Rear Brakes, 18" x 8" Fronts/20" x 10" Rears, Ordered: 1.26.17, Arrived: 3.29.17, First Start: 7.2.18, Go Cart: 11.4.18 Paint/Body: 2.23.19, Back Home: 11.24.19, Completed: NEVER!; View More Pics @
https://starmobileone.com/
-
Senior Member
Welcome to the party Peter! I look forward to following your build, its going to be even more fun than the one we did at build school. Going for a Blueprint engine?
Steve
Gen 1 '33 Hot Rod #1104
347 with Holley Sniper & Hyperspark, TKO600, IRS, 245/40R18 & 315/30R18, DRL, Digital Guard Dog keyless Ignition
-
Yup. Blueprint just makes it easier. Hope to order it this month.
- Peterh226 #1134
'33 Hot Rod 2nd Gen. Blueprint 383 Sniper TKO Delivered 4/14/2019
Full Fenders, Top, 3-Link, Wilwoods
YOKOHAMA ADVAN NEOVA AD08 R | Fr 245/45 R17 | Rr 295/30 R18
AR605 Torq-Thrust M Chrome | Fr 17x8 | Rr 18x10
-
Post Thanks / Like - 0 Thanks, 1 Likes
-
Steve >> aka: GoDadGo
Originally Posted by
peterh226
Yup. Blueprint just makes it easier. Hope to order it this month.
If you are going to be running an HEI Distributor then consider purchasing this little gem of a Rev-Limiter from MSD:
https://youtu.be/3C-IwoadX7Q
https://www.summitracing.com/parts/msd-8727ct
I've got this unit on my car and really works well and adjusts with the twist of two dials in 100 RPM increments.
Last edited by GoDadGo; 04-18-2019 at 03:00 PM.
-
Thanks, I'll add it to my research list!
- Peterh226 #1134
'33 Hot Rod 2nd Gen. Blueprint 383 Sniper TKO Delivered 4/14/2019
Full Fenders, Top, 3-Link, Wilwoods
YOKOHAMA ADVAN NEOVA AD08 R | Fr 245/45 R17 | Rr 295/30 R18
AR605 Torq-Thrust M Chrome | Fr 17x8 | Rr 18x10
-
Post Thanks / Like - 0 Thanks, 1 Likes
wrp liked this post
-
Hi Folks - Delivery Video
I'm working on having an automatic Video capture of the build. I'll explain in another set of posts, but here's a link to my first video. This one has a wider variety than what will be coming, but is still fun!
https://youtu.be/VQLDDTPj6TI
- Peterh226 #1134
'33 Hot Rod 2nd Gen. Blueprint 383 Sniper TKO Delivered 4/14/2019
Full Fenders, Top, 3-Link, Wilwoods
YOKOHAMA ADVAN NEOVA AD08 R | Fr 245/45 R17 | Rr 295/30 R18
AR605 Torq-Thrust M Chrome | Fr 17x8 | Rr 18x10
-
Post Thanks / Like - 0 Thanks, 2 Likes
-
Steve >> aka: GoDadGo
Welcome Fellow Dark Side Guy!
.........You Can't Beat Mighty Mouse Power!
-
Senior Member
CONGRATS!!! Other than good luck the first piece of advice I can give you is to get the body, doors, trunk, hood all fit up and aligned with each other (you will need to fit up the rad with the front grill as well) first before you get into all the other fun stuff!! This will not only test your patience but it will get you way ahead when it comes to the rest as that portion can go very quickly and the least amount of dust on it the better. This is a lesson I learned the hard way and now understand this is the way the other "full time builders" do it as well as at FFR. Doing body and fitment early on also lets you ensure good alignment for the rest of the components afterwards.
Oh and most of all HAVE FUN!!!
Black & Copper #1028 ("The Mistress" according to my wife!
)
Brought home: Nov. 2017, GoKart: May 2018, will be Plated & on the Road April 2020
Andreas
-
that's great advice! I am in the process of doing exactly that and have 10 - 15 hours in trying to hang the first door and it still isn't quite done. I am so glad to be getting this part of the build over with (while it is still cool in the shop). The rest will be a walk in the park.
-
I’m thinking about that process. I’m trying to find a post about the entire grind/sand/smooth process. I read a post but can’t find it again. It’s a bit overwhelming to decide where to start.
- Peterh226 #1134
'33 Hot Rod 2nd Gen. Blueprint 383 Sniper TKO Delivered 4/14/2019
Full Fenders, Top, 3-Link, Wilwoods
YOKOHAMA ADVAN NEOVA AD08 R | Fr 245/45 R17 | Rr 295/30 R18
AR605 Torq-Thrust M Chrome | Fr 17x8 | Rr 18x10
-
Firewall mounting
Centered and marked firewall for the pattern I wanted. Will be using button heads for final install.
E2CE8775-390F-4513-BE43-705FB26E186E.jpg
- Peterh226 #1134
'33 Hot Rod 2nd Gen. Blueprint 383 Sniper TKO Delivered 4/14/2019
Full Fenders, Top, 3-Link, Wilwoods
YOKOHAMA ADVAN NEOVA AD08 R | Fr 245/45 R17 | Rr 295/30 R18
AR605 Torq-Thrust M Chrome | Fr 17x8 | Rr 18x10
-
Post Thanks / Like - 0 Thanks, 1 Likes
wrp liked this post
-
- Peterh226 #1134
'33 Hot Rod 2nd Gen. Blueprint 383 Sniper TKO Delivered 4/14/2019
Full Fenders, Top, 3-Link, Wilwoods
YOKOHAMA ADVAN NEOVA AD08 R | Fr 245/45 R17 | Rr 295/30 R18
AR605 Torq-Thrust M Chrome | Fr 17x8 | Rr 18x10
-
Post Thanks / Like - 0 Thanks, 2 Likes
-
Member
You build Looks good. I see you got your door hinges. Im jealous, I’m still waiting on all my hinges . I called F 5 again today they said they expect them to ship with my floor parts this week.
-
Senior Member
and just when you hope all the powder coating is done, you find a few more parts that need it.... Starting to get into it Peter!
Gen 1 '33 Hot Rod #1104
347 with Holley Sniper & Hyperspark, TKO600, IRS, 245/40R18 & 315/30R18, DRL, Digital Guard Dog keyless Ignition
-
Painting
I want to get everything at least in primer before I start assembly. Created a spray booth out of an old shelving unit.
5158769C-4F48-43D9-8C22-6BB5ABD5D171.jpg
Lots of parts out for powder coat and a bunch of stuff on the POL. So, I’ll start some basic body work to slowly work my way into this stuff. I’m in no hurry, so enjoying the ride!
- Peterh226 #1134
'33 Hot Rod 2nd Gen. Blueprint 383 Sniper TKO Delivered 4/14/2019
Full Fenders, Top, 3-Link, Wilwoods
YOKOHAMA ADVAN NEOVA AD08 R | Fr 245/45 R17 | Rr 295/30 R18
AR605 Torq-Thrust M Chrome | Fr 17x8 | Rr 18x10
-
Post Thanks / Like - 0 Thanks, 1 Likes
-
Senior Member
I also see that the Gen 2 hard top fits better to the body and has more distinctive lines that line uop with the body better. I would be interested how the windows will go in if you have some. Nice Work.
Black & Copper #1028 ("The Mistress" according to my wife!
)
Brought home: Nov. 2017, GoKart: May 2018, will be Plated & on the Road April 2020
Andreas
-
The top did not fit that great - but with Persuasion (and bolting it in) I was able to get it all to line up. I'm hoping some time in the sun will relieve the stress a bit. The newer top does not have a liner which may provide more flex, but then more work to finish the inside.
- Peterh226 #1134
'33 Hot Rod 2nd Gen. Blueprint 383 Sniper TKO Delivered 4/14/2019
Full Fenders, Top, 3-Link, Wilwoods
YOKOHAMA ADVAN NEOVA AD08 R | Fr 245/45 R17 | Rr 295/30 R18
AR605 Torq-Thrust M Chrome | Fr 17x8 | Rr 18x10
-
Senior Member
Originally Posted by
peterh226
The top did not fit that great - but with Persuasion (and bolting it in) I was able to get it all to line up. I'm hoping some time in the sun will relieve the stress a bit. The newer top does not have a liner which may provide more flex, but then more work to finish the inside.
So the newer top has no inside liner other than the area where you can put in a sunroof if you wanted to??? Would appreciate seeing a picture of that id possible, that's a step back in my opinion. If I do another one, and knowing that, I would then do the ragtop instead, as well others may want to know that. TY!!
Black & Copper #1028 ("The Mistress" according to my wife!
)
Brought home: Nov. 2017, GoKart: May 2018, will be Plated & on the Road April 2020
Andreas
-
Post Thanks / Like - 0 Thanks, 1 Likes
wrp liked this post
-
Inside View of Top bolted in
Here you go... Note no Rubber seal at this point.
TopInside1.jpg TopInside2.jpg
- Peterh226 #1134
'33 Hot Rod 2nd Gen. Blueprint 383 Sniper TKO Delivered 4/14/2019
Full Fenders, Top, 3-Link, Wilwoods
YOKOHAMA ADVAN NEOVA AD08 R | Fr 245/45 R17 | Rr 295/30 R18
AR605 Torq-Thrust M Chrome | Fr 17x8 | Rr 18x10
-
Post Thanks / Like - 0 Thanks, 1 Likes
wrp liked this post
-
SS383 Badges
A little Solidworks modeling, 3D printing, and paint and I've got a logo for the car. Planning on badges on either side of the Cowl post and maybe on the rear. Sorry Ford guys, my car is what I want it to be!
IMG_1179.jpg
Next one will ge primed with SlickSand to smooth it out a but. Order of color is a bit tricky as well.
- Peterh226 #1134
'33 Hot Rod 2nd Gen. Blueprint 383 Sniper TKO Delivered 4/14/2019
Full Fenders, Top, 3-Link, Wilwoods
YOKOHAMA ADVAN NEOVA AD08 R | Fr 245/45 R17 | Rr 295/30 R18
AR605 Torq-Thrust M Chrome | Fr 17x8 | Rr 18x10
-
Post Thanks / Like - 0 Thanks, 1 Likes
-
Warped Door and Striker pin mount issue.
Got a chance to work on the doors this weekend. Drivers door has been giving me fits so I decided to give the passenger side a try.
I was able to get it to fit up quite easily. Still a bit more to do, but it's pretty close.
IMG_1270.jpg
On the passenger side...
IMG_1271.jpg
It's a big twist and I have no idea how to get it out.
At the front, the bracket for the Latch does not touch the door frame at the to hold the striker pin in place. I've got a gap of ~1/2 inch. Looks like I'll have the same on the other side. Maybe Gen 2 needs a different bracket.
bracket to body gap at striker pin.jpg
- Peterh226 #1134
'33 Hot Rod 2nd Gen. Blueprint 383 Sniper TKO Delivered 4/14/2019
Full Fenders, Top, 3-Link, Wilwoods
YOKOHAMA ADVAN NEOVA AD08 R | Fr 245/45 R17 | Rr 295/30 R18
AR605 Torq-Thrust M Chrome | Fr 17x8 | Rr 18x10
-
I’ve had similar struggles. My pass door went together fairly well but I also ended up with the same gap you’re showing. I ended up adding shim washers to cover the gap. I also had to cut down the collar of my door striker as it was too long and would not allow the door to close.
Drivers door has been a different story altogether, it kicked my butt. I have it close but can see that it would take quite a bit of glass work to get it 100%. I called and sent note to FF and have had great response from them, think I’ll end up trying a replacement door.
33 HotRod #1142
Started 5-9-19
Kingwood, Texas
-
They sent me a replacement drivers door, it was a little better than the original. I still needed shims to make it align with the body.
The top front of the door is off a bit where it meets the body, I'll need to do some grinding and glass work to make the fit look OK.
'33 Hotrod, #1047 Gen 1, delivered on 2/27/18, go cart on 9/24/18.
LS3 w/Gearstar Level 3 4L65e Tranny, Yank converter, Lokar shifter, Electric PS, Vintage AC/Heat/Def, 8.8" 3.55
TorqThrust II Wheels w/Toyo Proxy T1 Sport Tires, F 235/45ZR17 R 295/35ZR18
Garage Built, Driveway Painted.
-
Thanks Jim, I'll give them a call...
- Peterh226 #1134
'33 Hot Rod 2nd Gen. Blueprint 383 Sniper TKO Delivered 4/14/2019
Full Fenders, Top, 3-Link, Wilwoods
YOKOHAMA ADVAN NEOVA AD08 R | Fr 245/45 R17 | Rr 295/30 R18
AR605 Torq-Thrust M Chrome | Fr 17x8 | Rr 18x10
-
Here's what will need some work on to make it look decent.
Dscn3322.jpg
The other issue with both doors is the rear lower corner, it hits the body before the door closes, maybe some door seals will keep the inside of the door off the body.
'33 Hotrod, #1047 Gen 1, delivered on 2/27/18, go cart on 9/24/18.
LS3 w/Gearstar Level 3 4L65e Tranny, Yank converter, Lokar shifter, Electric PS, Vintage AC/Heat/Def, 8.8" 3.55
TorqThrust II Wheels w/Toyo Proxy T1 Sport Tires, F 235/45ZR17 R 295/35ZR18
Garage Built, Driveway Painted.
-
Senior Member
Originally Posted by
JimLev
Here's what will need some work on to make it look decent.
Dscn3322.jpg
The other issue with both doors is the rear lower corner, it hits the body before the door closes, maybe some door seals will keep the inside of the door off the body.
I had the same issue and unfortunately ground too much away from the door side and the bond let go between the two skins, so I had to add more fiberglass mat on the inside of the door in that area. I laid three layers of 1.5oz mat on that face lapping onto the top of the door where the window slot would go. I could have added to the body, however I was hesitant to do so as it has multiple layers of cloth and would be harder to get the same strength back due to the strength to thickness ratio of the cloth and resin. Regardless it seemed to work well and will only need to modify the window seal for the power windows.
20181223_104805.jpg You can see the crack in this pic before I corrected it.
Black & Copper #1028 ("The Mistress" according to my wife!
)
Brought home: Nov. 2017, GoKart: May 2018, will be Plated & on the Road April 2020
Andreas
-
Thanks for the pic and info AJT. Last night I ordered resin and mat. Think I'll do some glassing before the sanding.
'33 Hotrod, #1047 Gen 1, delivered on 2/27/18, go cart on 9/24/18.
LS3 w/Gearstar Level 3 4L65e Tranny, Yank converter, Lokar shifter, Electric PS, Vintage AC/Heat/Def, 8.8" 3.55
TorqThrust II Wheels w/Toyo Proxy T1 Sport Tires, F 235/45ZR17 R 295/35ZR18
Garage Built, Driveway Painted.
-
Blueprint Engine Specs for my build
WooHoo!! We're gonna have fun with this...
383_Dyno.jpg
- Peterh226 #1134
'33 Hot Rod 2nd Gen. Blueprint 383 Sniper TKO Delivered 4/14/2019
Full Fenders, Top, 3-Link, Wilwoods
YOKOHAMA ADVAN NEOVA AD08 R | Fr 245/45 R17 | Rr 295/30 R18
AR605 Torq-Thrust M Chrome | Fr 17x8 | Rr 18x10
-
Post Thanks / Like - 0 Thanks, 1 Likes
-
Originally Posted by
peterh226
Really Nice!
33 HotRod #1142
Started 5-9-19
Kingwood, Texas
-
Body progress - Radiator mounting
Got the passenger door fitted pretty well a couple of contact points when opening, but at least it’s close. After my fight (and loss) with the drivers door this is pretty good.
The radiator assembly is ok. The pieces didn’t line up too great but I got it all together. The tolerance difference between the radiator and the grill are a little more than I’d like and I will review some more before any final assembly. The condenser brackets also were pretty tight and I needed to grind some clearance on the grill. Definitely some bending to fit on all of this stuff.
The spacers you use with the a/c change some of the clearance as well, so more things to review. I’ll post some more details soon.
8AC44C23-A318-4BD2-B13E-8F4D5C85647F.jpeg
Looking forward to getting a bunch done next weekend.
- Peterh226 #1134
'33 Hot Rod 2nd Gen. Blueprint 383 Sniper TKO Delivered 4/14/2019
Full Fenders, Top, 3-Link, Wilwoods
YOKOHAMA ADVAN NEOVA AD08 R | Fr 245/45 R17 | Rr 295/30 R18
AR605 Torq-Thrust M Chrome | Fr 17x8 | Rr 18x10
-
Steve >> aka: GoDadGo
Originally Posted by
peterh226
Yes You Will!
Tire shredding will be surprisingly easy.
-
Senior Member
Gen 1 '33 Hot Rod #1104
347 with Holley Sniper & Hyperspark, TKO600, IRS, 245/40R18 & 315/30R18, DRL, Digital Guard Dog keyless Ignition
-
Radiator assembly
Got all of the parts trimmed and drilled. Condenser was not even with the face of the grill so I filed a bit away. Not sure why there is a difference, but it all looks ok. I put a spacer in for the upper mounts to better hold in place an not bend the brackets. Also got a couple of ordinary M16-2 nuts for temporary assembly purposes.
E6602E0B-4716-4AE9-9F0B-89D9B7760810.jpg98A5AEC5-656E-4816-A348-019122B06DCF.jpg
Looks like any serious suspension maintenance is going to require the radiator to be removed along with a bunch of stuff. Not worth obsessing about!
4E939047-BC12-472B-A23C-0021370D81F0.jpg
Now to fit the hood
- Peterh226 #1134
'33 Hot Rod 2nd Gen. Blueprint 383 Sniper TKO Delivered 4/14/2019
Full Fenders, Top, 3-Link, Wilwoods
YOKOHAMA ADVAN NEOVA AD08 R | Fr 245/45 R17 | Rr 295/30 R18
AR605 Torq-Thrust M Chrome | Fr 17x8 | Rr 18x10
-
Senior Member
33 Hot Rod #1133. LS/TKO600
Delivered 6-17-19. Started work 7-3-19. First start 9-6-19. First drive 9-24-19
Titled 2-28-20
MkI.IV 2643k
-
Senior Member
Looks good Peter. Interesting you had a bit of a clearance issue with the grill. Although the manual mentioned that the grill needed to be cut for the condenser, I found that it was already notched out and the clearance was great.
On Gen 2 do the engine side panels still rest on the lower extensions from the main body? If they do, I'm told that position of the body relative to the firewall, the engine side panels, and the hood should all be fitted at the same time as there is interaction between them all...
Steve
Gen 1 '33 Hot Rod #1104
347 with Holley Sniper & Hyperspark, TKO600, IRS, 245/40R18 & 315/30R18, DRL, Digital Guard Dog keyless Ignition
-
Nose cone and Engine Sides
Got the hood fitted. The gaps are a bit larger than I would have liked, but I think I will still do. Need to mount the hinge to see how motion affects the clearance.
Hood sides and Nose cone were not too bad to fit, but don't really align as I'd like.
- The Nose cose is OK on one side and short on the other. I measured the grill and it is the same distance from various points on the firewall to mounting locations on the grill. So I think the positioning of the Grill is reasonable. It's mounted pretty far back as well.
IMG_1318.jpg IMG_1319.jpg
At the front I guess I'm supposed to remove the Vertical flange and glass over the joint so it becomes one piece. I guess I can extend the one side at the same time.
The Sides fit up pretty well. Top mount to the grill is a little small as I needed to remove most of the flange to get it to line up with the grill.
However, as noted by others the top of the sides is a bit too high. The Half round from the hood will not line up.
IMG_1320.jpg IMG_1321.jpg
Options:
- see if there is some way to lower the nose cone so the sides are lower.
- try to pie cut the side panels and then glass them back together.
- Trim the hood and lose some of the half-round to the Hood/Side panel joint. The top would like up OK anyway.
I'm glad to be doing this now without any of the other mechanical parts getting in the way or dusty or damaged.
At least the Fenders and Running boards look pretty straightforward.
July4_frontB.jpg
Jason seems to be in the same Pickle. https://thefactoryfiveforum.com/show...od-Texas/page2 #45 shows about the same thing.
- Peterh226 #1134
'33 Hot Rod 2nd Gen. Blueprint 383 Sniper TKO Delivered 4/14/2019
Full Fenders, Top, 3-Link, Wilwoods
YOKOHAMA ADVAN NEOVA AD08 R | Fr 245/45 R17 | Rr 295/30 R18
AR605 Torq-Thrust M Chrome | Fr 17x8 | Rr 18x10
-
Senior Member
Question on the nose cone/under grill lip: Is yours two pieces or one? Mine was one piece and was long on each side and not trimmed back, I actually removed a good 2" when I setup mine. I find it very strange that it's now 2 pieces and you would need to laminate it together???? I would drop a note to Tony at FFR as I dont think this is right, I would be very surprised that they don't replace it. Here is a picture of mine, as you can sort of see (excuse the picture quality, lots of dust from sanding and cutting) that i needed to cut and trim it to that point and more.
20180715_110652.jpg
Black & Copper #1028 ("The Mistress" according to my wife!
)
Brought home: Nov. 2017, GoKart: May 2018, will be Plated & on the Road April 2020
Andreas
-
Looks like they went to 2 pieces with the Gen 2. @Michael101 is seeing the same issues I am. Time for a chat with FF.
- Peterh226 #1134
'33 Hot Rod 2nd Gen. Blueprint 383 Sniper TKO Delivered 4/14/2019
Full Fenders, Top, 3-Link, Wilwoods
YOKOHAMA ADVAN NEOVA AD08 R | Fr 245/45 R17 | Rr 295/30 R18
AR605 Torq-Thrust M Chrome | Fr 17x8 | Rr 18x10