Boig Motorsports

Visit our community sponsor

Thanks Thanks:  1
Likes Likes:  2
Results 1 to 30 of 30

Thread: FFR TYPE 65 For Sale

  1. #1
    Member
    Join Date
    Feb 2017
    Posts
    44
    Post Thanks / Like

    FFR TYPE 65 For Sale

    I have a Type 65 project for sale.

    The Type 65 has been professionally built and comes with the following:

    - Powerder Coated Frame
    - All components powder coated before installation
    - all new components, nothing was used or reused
    - Custom Built 302 350 HP Ford Crate Engine with Stack Induction by Pro-Formance Unlimited out of New Jersey.
    - New TKO 600 Tremac Transmission (manual)
    - 12.875 31 Spline drive shaft
    - 8.8 3 Link Rear Axle Housing on Axle
    - 11.65 Rear Brake Set
    - No Perch Rear Lower Control Arms
    - Front Tubular Lower Control Arms
    - Roaster / Coupe Solid Axle Coil Over Kit
    - Wilwood Brake and Clutch Set
    - Kirkey seats
    - vintage Air
    - 302 Headers - wrapped with heat fabric
    - Halibrand Replica Wheels with new rubber
    - removable steering wheel.
    - heat insulation installed.
    - professionally Painted

    It runs and drives and is nearly complete. It still needs the following to complete, interior carpet, dash cover, door handles, rear windows and front and rear windows installed, alignment, carburetor need to be synced and tuned. I have all the parts to complete it.

    Asking $35,000 US obo








  2. #2
    Senior Member John Dol's Avatar
    Join Date
    Feb 2011
    Location
    Gorham, ME
    Posts
    1,522
    Post Thanks / Like
    Unless you need the money, talk to Mark Dougherty, Mike Everson, or Jeff Kleiner to finish it for you. Your sooooooo close!!!!
    Gotta love that 8 stack

    GLWS

    John
    Last edited by John Dol; 05-15-2019 at 05:28 PM.
    Finished the "My Coupe, my way" project.

    http://s956.photobucket.com/albums/ae46/jdcoupe1969/
    Coupe #386,17" Team III 245 FR 315 RR, 3-link, T5, 4 wheel disk, power brakes/steering. Sniper EFI
    First start Sept. 18 2013 First go kart Sept 19 2013

  3. #3
    Senior Member JL1958's Avatar
    Join Date
    Jul 2013
    Location
    Atlanta
    Posts
    159
    Post Thanks / Like
    Where are you located?

  4. #4
    Member
    Join Date
    Feb 2017
    Posts
    44
    Post Thanks / Like
    The car is located in Cold Lake, Alberta, Canada.

  5. #5
    Mark Dougherty's Avatar
    Join Date
    Feb 2011
    Location
    Hershey PA
    Posts
    722
    Post Thanks / Like
    nice build
    The traveling Builder
    717-773-5624

  6. #6
    Member
    Join Date
    Feb 2017
    Posts
    44
    Post Thanks / Like
    Here is a video of the Type 65 running. This engine came from performance unlimited and the carbs have not been tuned or synchronized.

    https://youtu.be/r-wH_Sqwi_E

    If anyone is interested in looking at the engine build sheet please send me your email and I will send it to you.
    Last edited by Redmantice; 05-07-2019 at 10:28 PM.

  7. #7
    Senior Member Clover's Avatar
    Join Date
    Feb 2016
    Location
    Colorado
    Posts
    220
    Post Thanks / Like
    Wow, this seems like a heck of a deal. Sure looks nice to me and after buying a lot of these parts myself, I know there is great value here for someone. Not sure of your situation, but it seems like it would make sense financially to have the kit finished and then sell it. I would think you could pay someone to finish it off and then sell it for a good bit more but maybe that just does not work at this time for you. I hope you enjoyed the build and have something else fun on the horizon.
    Gen III Type 65 Coupe Delivered 6/26/2018

  8. #8
    Member
    Join Date
    Mar 2018
    Location
    Maryland
    Posts
    79
    Post Thanks / Like
    Geez, can somebody buy this car already so I stop thinking about it!

  9. Likes RandyNJ, JL1958 liked this post
  10. #9
    Junior Member
    Join Date
    Feb 2018
    Posts
    5
    Post Thanks / Like
    Is this car really still available?

  11. #10
    Member
    Join Date
    Feb 2017
    Posts
    44
    Post Thanks / Like
    Yes it is for sale. There have been a number of inquiries but no takers at this point.
    Regards,

    Jay

  12. #11
    Member
    Join Date
    Feb 2017
    Posts
    44
    Post Thanks / Like
    I have had a number of people privately e-mail me asking if I would sell for your $25,000 or lower. Although I respect the concept of a free market, I wanted to let people know not to waste their time. I am currently building an Vans RV10 experimental aircraft which is taking up all of my time. The Coupe is for sale because I have lost interest, not because I need the money. I will entertain offers in the range of $35,000 which is less than 1/2 of cost to build this Coupe. Thank you for your consideration.
    Regards,
    Jay
    Last edited by Redmantice; 05-25-2019 at 01:09 AM.

  13. #12
    Senior Member
    Join Date
    Feb 2011
    Location
    Myrtle Beach, SC
    Posts
    2,108
    Post Thanks / Like
    Jay-

    I think getting your car at your asking price is an absolute steal! If I had the money, and my wife wouldn't kill me, I would be at your place with a trailer in a minute!

    I am sorry that you have to sell it, but someone is going to get a terrific car at an amazing price!!

    Good luck with the sale; frankly, I am shocked that someone hasn't snatched it up already!

    And good luck with your aircraft build! I know this is a Factory Five forum, but I would love to see pictures of your project.

    All the best!

    Regards,

    Steve

  14. #13
    Member bsnyder's Avatar
    Join Date
    Feb 2011
    Location
    Spanaway WA
    Posts
    69
    Post Thanks / Like
    Blog Entries
    1
    PM sent.

  15. #14
    Senior Member John Dol's Avatar
    Join Date
    Feb 2011
    Location
    Gorham, ME
    Posts
    1,522
    Post Thanks / Like
    Quote Originally Posted by WIS89 View Post
    Jay-

    I think getting your car at your asking price is an absolute steal! If I had the money, and my wife wouldn't kill me, I would be at your place with a trailer in a minute!

    Good luck with the sale; frankly, I am shocked that someone hasn't snatched it up already!
    I feel the same way. I'm almost done with mine but would love to snatch it up. The wife part is the biggest scare! LOL

    Somebody buy this already so I can stop thinking about it.

    GLWS

    John

    PS and $25K is a slap in the face, common people know what your bidding on.
    Finished the "My Coupe, my way" project.

    http://s956.photobucket.com/albums/ae46/jdcoupe1969/
    Coupe #386,17" Team III 245 FR 315 RR, 3-link, T5, 4 wheel disk, power brakes/steering. Sniper EFI
    First start Sept. 18 2013 First go kart Sept 19 2013

  16. #15
    Member
    Join Date
    Feb 2017
    Posts
    44
    Post Thanks / Like
    This Coupe is sold pending funds....

    Thank you everyone for your support. I’m now officially down to one FFR (33 Hot Rod) and my Vans RV10 project.

    Last edited by Redmantice; 05-26-2019 at 09:34 PM.

  17. #16
    mburger's Avatar
    Join Date
    May 2017
    Location
    Punta Gorda FL
    Posts
    1,146
    Post Thanks / Like
    Love the RV10!
    Mark
    Mk1, Frame #1929 Complete restoration/upgrade. BP 347 with Edelbrock PF4 439/420. 4 link with coilovers. 8.8 3.55, 15” Halibrand, New beefed up T5 w/short throw shifter, Power 4 wheel disc brakes, Custom original style steering wheel, shaft and boss, Heat/AC, Heated seats, PPW wipers w/washers, Forte’s throttle linkage, RT trunk hoop mod, Pusher cooling fans, full LED lighting, custom headrests, 5 point seat belts with sub pass through, Speedhut GPS gauges, battery drop box in trunk, LED courtesy lights, Breeze trunk cubby kit.

  18. #17
    Junior Member
    Join Date
    May 2019
    Posts
    1
    Post Thanks / Like
    PM Sent

  19. #18
    Member
    Join Date
    Jun 2018
    Location
    South Central WI
    Posts
    44
    Post Thanks / Like
    Glad this is sold. My son has been trying to convince me the coupe is a better option than the roadster and cost is one of the reasons I give him for sticking with our roadster plans. This is/was one heck of a deal!

  20. #19
    Member
    Join Date
    Feb 2017
    Posts
    44
    Post Thanks / Like
    UPDATE: THE COUPE IS BACK IN THE MARKET.

    The previous buyer unceremoniously backed out.

    If you have any questions, please let me know.

    Regards,

    Jay
    Last edited by Redmantice; 05-31-2019 at 11:20 PM.

  21. #20
    Junior Member
    Join Date
    Sep 2013
    Posts
    8
    Post Thanks / Like
    What would be involved in getting it into US? Could someone just load it into a trailer and drive it back across the border?

  22. #21
    Member
    Join Date
    Feb 2017
    Posts
    44
    Post Thanks / Like
    I’m getting a lot of questions on the paperwork. It has been started. I have the Manufacturers Certificate of Origin and the VIN number. It is registered as a Factory Five 1965 Replica.

    Regards,

    Jay

  23. Thanks bcorner thanked for this post
  24. #22
    Junior Member
    Join Date
    Apr 2017
    Posts
    2
    Post Thanks / Like
    Quote Originally Posted by Redmantice View Post
    UPDATE: THE COUPE IS BACK IN THE MARKET.

    The previous buyer unceremoniously backed out.

    If you have any questions, please let me know.

    Regards,

    Jay
    I may have missed this, but is it Gen 2, or Gen 3? Thanks.

  25. #23
    Member
    Join Date
    Feb 2017
    Posts
    44
    Post Thanks / Like
    This is a Gen 1 kit.

  26. #24
    Junior Member
    Join Date
    Feb 2018
    Posts
    5
    Post Thanks / Like
    Serious question, anyone have any suggestions on transporting something like this to the US? It would be a 5000 mile, 75 hour round trip drive to the southeast where i live which just wouldn't be practical. Not having an active passport doesn't help either. I sure would be interested, just have no idea how I would get it. Anyone ever brought an incomplete kit over from Canada before?

  27. #25
    Senior Member John Dol's Avatar
    Join Date
    Feb 2011
    Location
    Gorham, ME
    Posts
    1,522
    Post Thanks / Like
    Quote Originally Posted by RyanP View Post
    Serious question, anyone have any suggestions on transporting something like this to the US? It would be a 5000 mile, 75 hour round trip drive to the southeast where i live which just wouldn't be practical. Not having an active passport doesn't help either. I sure would be interested, just have no idea how I would get it. Anyone ever brought an incomplete kit over from Canada before?
    Contact a car shipping company. Cost me about $1,600 to ship East to West coast.


    Good luck,


    John
    Finished the "My Coupe, my way" project.

    http://s956.photobucket.com/albums/ae46/jdcoupe1969/
    Coupe #386,17" Team III 245 FR 315 RR, 3-link, T5, 4 wheel disk, power brakes/steering. Sniper EFI
    First start Sept. 18 2013 First go kart Sept 19 2013

  28. #26
    Member Zots's Avatar
    Join Date
    Sep 2017
    Location
    Montgomery TX
    Posts
    63
    Post Thanks / Like

  29. #27
    Member
    Join Date
    Feb 2017
    Posts
    44
    Post Thanks / Like
    The Daytona is still for sale.

    For a limited time I am prepared to include the 24’ x 8’ Hallmark Car Hauler that is pictured in the video link above for the original listed price of $35,000 US firm. I need to make room for my other toys.

    First non refundable $1,000 deposit takes it.

    Jay

  30. #28
    Senior Member
    Join Date
    Feb 2011
    Location
    Myrtle Beach, SC
    Posts
    2,108
    Post Thanks / Like
    Quote Originally Posted by Redmantice View Post
    The Daytona is still for sale.

    For a limited time I am prepared to include the 24’ x 8’ Hallmark Car Hauler that is pictured in the video link above for the original listed price of $35,000 US firm. I need to make room for my other toys.

    First non refundable $1,000 deposit takes it.

    Jay
    Jay-

    You are killing me!!! This is an insane deal.

    You know, I could store it for you, take very good care of it, and send you periodic pictures of me "test driving," yeah that's it "test driving" it for you, until you wanted it back.

    Somebody is going to get an amazing deal on a beautiful car!! Good luck with the sale Jay.

    Regards,

    Steve

  31. #29
    Member
    Join Date
    Feb 2017
    Posts
    44
    Post Thanks / Like
    The car is sold for sure this time.
    Cheers.
    Jay

  32. #30
    Senior Member John Dol's Avatar
    Join Date
    Feb 2011
    Location
    Gorham, ME
    Posts
    1,522
    Post Thanks / Like
    Congrats!

    John
    Finished the "My Coupe, my way" project.

    http://s956.photobucket.com/albums/ae46/jdcoupe1969/
    Coupe #386,17" Team III 245 FR 315 RR, 3-link, T5, 4 wheel disk, power brakes/steering. Sniper EFI
    First start Sept. 18 2013 First go kart Sept 19 2013

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Martin's Dent and Collision Shop

Visit our community sponsor