Very Cool Parts

Visit our community sponsor

Thanks Thanks:  0
Likes Likes:  0
Results 1 to 5 of 5

Thread: Help with Hardware

  1. #1
    Senior Member TomH33's Avatar
    Join Date
    Nov 2016
    Location
    Parker,CO
    Posts
    108
    Post Thanks / Like

    Help with Hardware

    Hi
    I am just about ready to mount the body for the final time and I would like to know where all this hardware gets used. Not a picture in the manual of any mounting hardware usage, except lower door sill revits and two rear body mounting points. There are at least 35 bolts, nut, and washers in one package and about 15 rubber grommets in two sizes with screws in an other. See the pictures.

    I’m at a lost as to were all this hardware is used and any help would be appreciated.

    I know to rivet the door sills, the fire wall (mix of rivets and screws/rivnuts), and the two large bolts that go through the under fender area. These mounting points would not use grommets and only use a few bolts. This is all the info I gathered from the manual.

    Thanks TomH33_DSC0183.jpg

  2. #2
    Senior Member JOP33's Avatar
    Join Date
    Dec 2016
    Location
    Haslet, Texas
    Posts
    1,009
    Post Thanks / Like
    I believe the front horns on the body also get attached to the triangular kick up front.
    33' Hot Rod Coupe/Roadster (GEN 1), Fendered, Ford 302, 350hp, EFI, AOD, 4-Link, Double Adjustable Koni Coilovers, Split Rear Exhaust, Electric Power Steering, AC/Heat/Defrost, Moser 8.8"-3.55, Willwood Front/Rear Brakes, 18" x 8" Fronts/20" x 10" Rears, Ordered: 1.26.17, Arrived: 3.29.17, First Start: 7.2.18, Go Cart: 11.4.18 Paint/Body: 2.23.19, Back Home: 11.24.19, Completed: NEVER!; View More Pics @ https://starmobileone.com/

  3. #3
    Senior Member HVACMAN's Avatar
    Join Date
    May 2017
    Location
    Village Mills, Texas
    Posts
    674
    Post Thanks / Like
    If I remember correctly the seat mounting hardware is in that package, but I could be wrong. (I'm old)
    33 Hot Rod (Gen 1) Stage 1 delivered on 4/27/2017, Stage 2 delivered on 9/21/2018
    LS3 495hp/480 lb. ft., 4L70E, Electric PS, Classic Auto Air, Lokar electronic sport shifter, 13 inch Wilwood front and 11.68 Cobra rear brakes, Ford 8.8 w 3.73 w 4 link, Billet Specialty Legend Series MAG wheels and Mickey Thompson
    Sportsman S/R 26x8x18 front and 29x18x20 rear tires.

  4. #4
    Senior Member
    Join Date
    Nov 2017
    Location
    Placitas, NM
    Posts
    1,443
    Post Thanks / Like
    My seat hardware was in a seperate bag, the bolts were about 2.5" to 3" long IIRC, I'm old too.
    '33 Hotrod, #1047 Gen 1, delivered on 2/27/18, go cart on 9/24/18.
    LS3 w/Gearstar Level 3 4L65e Tranny, Yank converter, Lokar shifter, Electric PS, Vintage AC/Heat/Def, 8.8" 3.55
    TorqThrust II Wheels w/Toyo Proxy T1 Sport Tires, F 235/45ZR17 R 295/35ZR18
    Garage Built, Driveway Painted.

  5. #5
    Senior Member
    Join Date
    Nov 2015
    Location
    Elverta, CA
    Posts
    401
    Post Thanks / Like
    The flat head screws (some) go through side panels into the cowl. The bumpers go on cowl, hood, and other spots when hood closes. Book has them in hood fitment and final body install section, I think.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Breeze

Visit our community sponsor