These features are all available in the Big Brother LCD gauge Systems, but for those wanting to keep their mechanical gauges,
and nostalgic theme, this is a great module to simplify wiring, as well as add some logic to your vehicle.
This works with ANY CAR, ANY ENGINE.
Named the PRO-BCM-100/200 because it acts like a Body Control Module to trigger lighting, pumps, fans, or virtually anything
you prefer. The device will not interfere with your engine function as it is a stand-alone setup. Minimal wiring is required
to power and manipulate devices. As shown in the diagram, the interface can be wired for switches directly to the box, as opposed
to feeding extra wires from the vehicle's electrical system.
For instance, a single switch wired to ground can control turn signals, and hazards with preset blinking patterns. There is
no need for flashers, or complex connections. Simply connect the trigger wire to the respective relay. The outputs will
also drive LED lights without the need for resistors.
A single sensor can be programmed to activate one or more fans based on input temperature. Use auxiliary fans and
temperature sampling for transmission pumps, fans, etc.
Use pressure sensors to run priming sequences for fuel pumps to allocate extra current for engine cranking. May be
connected to Steering Wheel buttons, or console mounted buttons.
The system can be setup to run electric water pumps and radiator fans after engine shut down for preset times. This
is great for boosted cars, or any engine for cool down.
Either model is capable of sensing out of range temperature and pressure to flash a Status/Trouble LED
that can be mounted on your dash or console.
Example of 100 series wiring diagram:
For the 200 series module, use your Windows based computer to Log information in real-time,
or troubleshoot the input and output signals. The log files are saved as CSV format that can
be opened and graphed in most spreadsheets.
The differences between the 100 and 200 models are listed below.
Request customized control circuits for your application like window controls, door poppers, etc.!
PRO-BCM-100, $300 CDN
2 Door inputs [Digital]
2 Signal inputs [Digital]
1 Pressure Sensor Input [Analog]
1 Temperature Sensor Input [Analog]
1 Shift LED Output
1 Status/Trouble LED Output
1 Right Lamp/LED Output
1 Left Lamp/LED Output
1 Dome / Courtesy Lamp / LED Output
Tachometer input [5V PCM or 12V Pulsed]
PRO-BCM-200, $450 CDN
GPS sensor
Customized Circuit capable
Logging and Test Software for Windows based computers via USB 2.0/3.0
Tachometer input [5V PCM or 12V Pulsed]
LED Turn Signal capable
1 Shift LED Output
1 Status/Trouble LED Output
1 Dome / Courtesy Lamp / LED Output
12 Digital Inputs
10 Analog Inputs
14 Digital Outputs
As always, post your questions here, PM, or email!
Thank you,
Tino
Last edited by LCD Gauges; 06-20-2019 at 11:11 AM.
Reason: edits in blue
Custom LCD Gauges , Data Loggers, Control Touch Screens www.LCDdash.com \\ 647-522-9953 \\ Voice & Text Proud new owner of GTM Gen 1., #105 - 08/27/11
LQ9 Powered, G96.00 6 speed transaxle
I'm not well versed with Android, but the possibility is there if the demand is high enough.
Once I get caught up on my current tasks, I'll dedicate some time to learning Android and Apple iOS,
or hopefully find a programmer that can do the job!
Additional edits in blue text above.
Last edited by LCD Gauges; 06-20-2019 at 11:11 AM.
Custom LCD Gauges , Data Loggers, Control Touch Screens www.LCDdash.com \\ 647-522-9953 \\ Voice & Text Proud new owner of GTM Gen 1., #105 - 08/27/11
LQ9 Powered, G96.00 6 speed transaxle