How did you all finish your dash ? Paint / Material ? Pic please
Visit our community sponsor
How did you all finish your dash ? Paint / Material ? Pic please
I used a mix of 3M stick on fake carbon fibre and black plastic (leather look) similar to the stuff that comes with the roadster kits. I attached the dash with 10-32 SS socket head screws
dash3.JPG
David W
Mkll 4874 built in 2004
Gen 3 coupe #16 registered 2018 painted 2019
Went kind of a different route,
Jonas
_____________________
Check out our build blog - https://vjjfactoryfive.wordpress.com/
FFR Type-65 Coupe 720
London Ontario Canada
I'm using a combination of regular vinyl and carbon fiber looking vinyl (both matched from my Corbeau seats) and red stitching. Similar for the door cars. All fasteners hidden and not using the brow piece. Just picked up everything from the auto upholstery shop today. Should be posting pics in my build thread in the next week or two.
Build 1: Mk3 Roadster #5125. Sold 11/08/2014. Build 2: Mk4 Roadster #7750. Sold 04/10/2017. Build Thread
Build 3: Mk4 Roadster 20th Anniversary #8674. Sold 09/07/2020. Build Thread and Video. Build 4: Gen 3 Type 65 Coupe #59. Gen 3 Coyote. Legal 03/04/2020. Build Thread and Video
Build 5: 35 Hot Rod Truck #138. LS3 and 4L65E auto. Rcvd 01/05/2021. Legal 04/20/2023. Build Thread. Sold 11/9/2023.
51C9123B-4D2B-4F03-8E7F-35B58BF09692.jpeg
51E6B47E-BD02-4433-A70B-6A47C32681C0.jpeg
Aluminum covered with 1/16 foam then vinyl covering.
Fastened with 6-32 button head Allan screws with washers.
John
Finished the "My Coupe, my way" project.
http://s956.photobucket.com/albums/ae46/jdcoupe1969/
Coupe #386,17" Team III 245 FR 315 RR, 3-link, T5, 4 wheel disk, power brakes/steering. Sniper EFI
First start Sept. 18 2013 First go kart Sept 19 2013
Hi David, looks nice man.
Where did you get that shifter? Am trying to look for options, will have a mid shifter by the way.
Anything would help, thx,
Tim
Take a look at what I did here.
post 135 shows the near final results. several posts earlier I show the process.
https://thefactoryfiveforum.com/show...pe-Build/page4
Not finished and still very rough fitting, but I'm going for an aircraft cockpit style finish:
IMG_1738.jpg
IMG_1740.jpg
Going the cheap route (which I can always upgrade later), I machined the switch bezels from plate aluminum and a handheld router in a jig, then spray painted them with BBQ grill paint. Anodizing would have been preferable, but I wanted to see how they looked before I committed. Although the grill paint with a very light sweep of a scotchbrite in one direction did a pretty good job!
Stitch work was done by the local upholstery shop for about $240.
Resettable fuses will fill the holes up top and a New Vintage switch panel will fill that hole in the bottom:
tn_21101-side__31164.1455406244.1280.1280.jpg
Still trying to decide how I want to finish the gauge cluster.
Last edited by Alphamacaroon; 09-22-2019 at 10:59 PM.
Carbon fiber vinyl. 20190919_162134.jpg
33 Hot Rod w/ deluxe 32 nose
350 SBC and 700r4 automatic, 8.8 rear with 3.55 gears
Order date:4/25/19, Deliver date 6/10/19
First run 10/6/2019, Go cart 11/3/2019