FormaCars

Visit our community sponsor

Thanks Thanks:  6
Likes Likes:  12
Results 1 to 12 of 12

Thread: Best Soundproof material and practice...

  1. #1
    Member
    Join Date
    Sep 2019
    Location
    Fredericksburg, VA
    Posts
    42
    Post Thanks / Like
    Blog Entries
    1

    Best Soundproof material and practice...

    Howdy,

    Iím trying to narrow down what would be the best material for soundproofing.

    Does anyone have experience with a few brands out there? Or is the general consensus on a particular brand?

    Just trying to get an idea for 2 scenarios:

    1. Disregard of cost for best material

    2. Most cost effective material (bang for the buck)


    As for best practice, is it best to ďLizardskinĒ + ceramic coat the firewall side of the panels and floor panels and then cover with soundproof the entire cockpit area?

    Any other recommendations?

    Thank you. Iím attaching an interesting article regarding the soundproof materials.

    https://soundproofliving.com/automot...ing-materials/

  2. #2
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    6,205
    Post Thanks / Like
    Similar to your power steering question, you're asking for "best" when (1) Most of us will recommend what we've successfully used, and (2) No actual testing data at least in these builds between various brands. So you'll get lots of opinions but no one can really say theirs is "best" or "best practice." What I can say for me, after several builds and thousands of miles, is (1) A decent heat/sound insulation installation on the inside of the cockpit along with the carpet and I've had zero heat issues. (2) Be just as conscious of air intrusion into the cockpit. It's critical to get everything sealed up so that hot air from the engine compartment isn't coming into the cockpit. All the insulation in the world isn't going to help if hot air is flowing in. And (3) Don't underestimate that big orange ball in the sky. We get worn out from heat and sun from outside the car way before heat inside the car is an issue. Kind of goes with the territory of an open top Roadster.

    Products I've used? Dynamat stuff is all good, just pricey. I used some Second Skin Damplifier Pro in my Coupe build and was very impressed, but also not particularly cheap. I've used Lizard Skin heat and sound products on all my builds and like it a lot. A good coating of both on the inside plus carpet has been my main strategy, and I've found it works fine. No additional material required. And I don't recommend it on the engine or chassis side, even though I know some do it. It's a water based product and while it dries hard I personally don't consider it hard and durable enough to be left uncovered. Plus I strongly prefer the clean look of metal (however you choose to finish it or not) and it's just not needed there in my experience.
    Last edited by edwardb; 10-07-2019 at 08:48 AM.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014.
    Build 2: Mk4 Roadster #7750. Sold 04/10/2017. #7750 Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. 03 of 20. 2015 crate Coyote, 2015 IRS. Legal 04/18/2017. #8674 Build Thread and Video
    Build 4: Gen 3 Type 65 Coupe #59. Gen 3 crate Coyote. Delivered 12/2/2017. #59 Coupe Build Thread

  3. Thanks Aircontroller, BLUE KNIGHT thanked for this post
    Likes Aircontroller, BLUE KNIGHT liked this post
  4. #3
    Senior Member
    Join Date
    Sep 2015
    Location
    Hamersville, Ohio
    Posts
    364
    Post Thanks / Like
    I used the lizardskin products on my car, however it’s still a work in progress, so I can’t vouch for its effectiveness. So far, I’ve only done my top, but when I do my side & firewall panels, I plan to apply it to the back sides so that my interior is all metal.

  5. Likes Aircontroller liked this post
  6. #4
    Senior Member
    Join Date
    Sep 2017
    Location
    Alliston, Ontario, Canada
    Posts
    324
    Post Thanks / Like
    I used Hushmat after seeing it recommended on here and doing some research. Never felt like my footboxes were getting hot in two seasons of driving. As noted above the sun will heat up absolutely everything though.
    2017 FFR MK4, 3 Link, 15" FFR halibrands, cooper cobra tires, '88 302/5.0, GT40 Y303 heads, Performer RPM intake Manifold, Holley 650 DP Carb, Pertronix distributor, T5Z spec built transmission, 3.73 rear end. Ordered Nov 2016, picked up at FFR Feb 2017, first start July 2017, Legal on the road May 2018, still in Gelcoat.

  7. Likes Aircontroller liked this post
  8. #5
    Tool Baron frankeeski's Avatar
    Join Date
    Feb 2011
    Location
    "The I.E." SoCal
    Posts
    1,094
    Post Thanks / Like
    After a number of builds, I use Fatmat ordered directly from their website. It's inexpensive when compared to the the other name brands and has performed well in every car we have done.
    Frank
    __________________________
    Factory Five Racing MKIII Super Snake Replica. Cannonball Cobra Drop Trunk Box, Horn Button and other machined Do Dads.
    i.e.427 Chromed Full Width Roll Bar with integrated LED Third Brake Light.
    I will never forget My Buddy Paul.

  9. Likes Aircontroller liked this post
  10. #6
    Senior Member lewma's Avatar
    Join Date
    Jan 2018
    Location
    San Marcos, CA
    Posts
    169
    Post Thanks / Like
    Blog Entries
    2
    I used dynomat+carpet on my MK4 but I wouldn't know if it makes a difference or not. All you can hear are the side pipes anyway. Ditto what edwardb says above with regards to hot air flowing in from the engine bay. I'm tracking that down now on my car.
    Mk4 Complete Kit #9312 ordered 1/27/18, Delivered 3/24/18, DMV start 7/26/19, DMV done 9/11/19 - Coyote, IRS, Power Steering, Wilwood Brakes, 17" Halibrand

  11. Likes Aircontroller liked this post
  12. #7
    Senior Member Paul_M's Avatar
    Join Date
    Nov 2015
    Location
    Westchester, NY
    Posts
    130
    Post Thanks / Like
    I used Lizard Skin ceramic and sound insulation for my build. Just used it in the cockpit, including firewall. I made sure to plug up any holes prior to applying it, and tapped up any possible places it could come out. There is a decent amount of prep work. Also I had all my panels powder coated so the interior of the cockpit had to be sanded with an orbital sander. Was very happy with the results and while I only have 1k miles on the car haven't had any heat issues. Would use it again.
    MK4 20th Anniversary Roadster #8692 - #9 of 20
    Purchased Aug 2015 - Street Legal July 2019
    Graduation Thread: https://thefactoryfiveforum.com/show...ry-MK4-9-of-20

  13. Likes Aircontroller liked this post
  14. #8
    Senior Member Avalanche325's Avatar
    Join Date
    Nov 2011
    Location
    Jax Beach, FL
    Posts
    1,281
    Post Thanks / Like
    Soundproofing? In a Cobra with sidepipes next to your ear? Hahahahahahaha.

    Heat insulation. That makes sense.

    As edwardb said, most people, me included, have used precisely one product. So not many of us can really compare. But, from my years around here. My advice is be concerned more about heat control. Also, some products are heavy, which is exactly what a Cobra is not supposed to be. 50lbs is more than a 2% weight gain. I remember that someone said they used a product that added 100lbs. Doesn't sound like much, but it is significant if you are concerned with performance.

    I used EZ-cool. Which is a lightweight heat barrier.

  15. Thanks Aircontroller thanked for this post
    Likes Aircontroller liked this post
  16. #9
    Junior Member
    Join Date
    Mar 2019
    Posts
    6
    Post Thanks / Like
    Hi, I know this is not the preferred method to apply Lizard Skin but i'm going to use a brush. Is it possible to thin the Lizard Skin down so it is more easily applied with a brush?

    thanks,
    Tim

  17. #10
    Papa's Avatar
    Join Date
    Dec 2016
    Location
    Parker, CO
    Posts
    2,155
    Post Thanks / Like
    I did the entire interior of my car with ThermoTec Coolmat. Pretty much the same as Dynomat and other similar products. I did it more for sound dampening. I didn't want that tin can sound in the car. It is heavy at about 40-45 lbs.

    Dave
    There are 10 types of people in this world;
    those who understand binary and those who don't.

    My Build Thread: http://thefactoryfiveforum.com/showt...ter-Build-9754

  18. Thanks Aircontroller thanked for this post
    Likes Aircontroller liked this post
  19. #11
    Member
    Join Date
    Sep 2019
    Location
    Fredericksburg, VA
    Posts
    42
    Post Thanks / Like
    Blog Entries
    1
    Hey Tim, I’m not an expert nor have I applied LS but the instructions are to ensure that you have a certain thickness to the product on the surface. I think they supply you with a little measuring tab that you can crosscheck that stuff with.

    So in the end, I guess as long as you can ensure the thickness of the LS on the surface of the material, you might be good to go.

    But then again, the demo was specific about how much stirring you had to do because of some of the components in the chemical. So I dunno.

    If you haven’t seen the vid, go to the LS webpage, you’ll see it. I can see why you would opt to do that to prevent from aerating that stuff especially if you’re in a confined space and can’t go outside.

    Quote Originally Posted by tbl100 View Post
    Hi, I know this is not the preferred method to apply Lizard Skin but i'm going to use a brush. Is it possible to thin the Lizard Skin down so it is more easily applied with a brush?

    thanks,
    Tim

  20. Thanks tbl100 thanked for this post
    Likes tbl100 liked this post
  21. #12
    Senior Member edwardb's Avatar
    Join Date
    Feb 2011
    Location
    Lake Orion, Michigan
    Posts
    6,205
    Post Thanks / Like
    Quote Originally Posted by tbl100 View Post
    Hi, I know this is not the preferred method to apply Lizard Skin but i'm going to use a brush. Is it possible to thin the Lizard Skin down so it is more easily applied with a brush?

    thanks,
    Tim
    It's water based, so could be thinned a bit with water. Not sure it would be necessary though. I've brushed it on smaller pieces (both products) and while slower than spraying, can be done. I'd be afraid of not getting the required thickness if thinned though. BTW, spraying is the easy part. Literally just takes minutes to do the entire interior and trunk. And relatively easy to get the required thickness with a couple coats. The time is in the masking and prep. Just like all spray jobs.
    Build 1: Mk3 Roadster #5125. Sold 11/08/2014.
    Build 2: Mk4 Roadster #7750. Sold 04/10/2017. #7750 Build Thread
    Build 3: Mk4 Roadster 20th Anniversary #8674. 03 of 20. 2015 crate Coyote, 2015 IRS. Legal 04/18/2017. #8674 Build Thread and Video
    Build 4: Gen 3 Type 65 Coupe #59. Gen 3 crate Coyote. Delivered 12/2/2017. #59 Coupe Build Thread

  22. Thanks tbl100 thanked for this post
    Likes tbl100, Aircontroller liked this post

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Lodestone Billetworks

Visit our community sponsor