Has anyone put a bracket on the lower radiator hose to help support it at the cross bars?
I am trying to find something that might work. Or is the consensus that it doesn’t need one.
Thanks
Visit our community sponsor
Has anyone put a bracket on the lower radiator hose to help support it at the cross bars?
I am trying to find something that might work. Or is the consensus that it doesn’t need one.
Thanks
Mk4 ordered 1/3/18, IRS, Coyote, T56 Magnum
I felt it was needed for my configuration and this is what I did:
31117BD4-B607-47BD-9C15-165E61435EBB.jpg
Chris
Generation 3 Type 65 Daytona Coupe Complete Kit #151885 received May 6, 2022. Gen 3 Coyote, IRS, Tremec TKX, American Powertrain hydraulic throwout bearing & Wilwood brakes.
MK4 Basic Kit #7404, 347 EFI - Pro M Racing ECM, 30# injectors, 70 mm throttle body, 80 mm MAF, Edelbrock Performer aluminum heads & RPM II intake, all new G-Force T5, 3:55 gears, Pro 5.0 shifter, 3-link, carbon fiber dash/custom Speedhut gauges and paint by Da Bat.
Depends on your hose / pipe. I used the ones from Breeze and I put a stick on rubber isolator on the round tube under it to prevent rubbing and it’s been fine. With solid pipes you may not want to fix them as that would restrict a lot of movement and could cause issues. The FFR stainless hose flexes and probably could be clamped. The answer depends on your routing and what your using.
Mk4, Moser M88 rear end, Eaton truetrak, Craft Racing 461 Windsor, MMR pro trans, Glenn’s 1,000 hp cobra fuel system and lots of other parts.
Breeze has a bracket on their site. https://www.breezeautomotive.com/sho...k3-1-roadster/ I rounded the bracket tabs to conform to the round X-cross bar.
Last edited by boat737; 12-02-2018 at 12:18 PM.
If Brute Force doesn't work, you're not using enough of it.
Basic Stuff: MK4 Complete Kit #8439, Wilwood's, 17" Halibrands. Extra Stuff: Stainless brake and fuel lines, Breeze cooling, Battery mount, SS Roll Bar. Old Fart Stuff: Heater, Seat Heaters, Footbox Fresh Air, Stereo, Keyless ignition, Power Steering, Hyd Clutch.
Young & Dumb Stuff: 427w Dart, TKO600, 3 link Moser M9/Ford 9", 3.5:1, Eaton TruTrac Posi. Graduation Thread
All of them I build get a 20 cent conduit clamp from the hardware store.
Jeff
hoseclamp.jpg
There you go Jeff!!! A 20 cent upgrade! Wait till da Bat hears this!
FFR 5136 Started as a donor...donor guages, engine, trans,etc. Now...TFS street intake,stage 1 cam, GT40p's,24# injectors and 80mm MAF,70mm TB,Z-spec t-5, and PSE Halibrand wrapped with Nitto 555 G2’s. My ever evolving dream car!!
Have the Breeze stainless steel COYOTE lower hard pipe with the $0.20 solution. Recommend the Breeze pipe over the FFR pipe.
Last edited by BEAR-AvHistory; 12-02-2018 at 03:35 PM.
Kevin
MKIV #8234
Coyote '14/TKO-600/3-Link 3:55 Rear
I love the smell of 100 octane in the morning.
NITTO NT01 275X40X17ZR - 315X35ZRX17
Delivered 2/7/14 - Plate "COYOTE NC1965" 3/25/15
I used Breeze for the upper. They didn’t have a hose for the bottom with a Coyote. They did recommend Boig Motorsports for the lower. It is a contoured stainless tube with hose on either end.
Mk4 ordered 1/3/18, IRS, Coyote, T56 Magnum
I used a chrome coil cover bracket I got from my local auto parts store. Its made for the ignition coil but I repurposed it after I retrofited a hotter coil from a fox body mustang EFI car.
Here is what it looks like.
https://www.4wd.com/p/mr-gasket-comp...AaAreJEALw_wcB
F5R9196 Hand built 347 475hp EFI | T5Z | LSD 3.73 3-link | Power Steering | Power Brakes | Vintage Air | 315/35ZR17 & 275/40ZR17 NT555
HAGERTY. DRIVERS CLUB | Texas Cobra Club
31117BD4-B607-47BD-9C15-165E61435EBB.jpg
Chris[/QUOTE]
I’m probably gonna feel dumb when you tell me, but what are the two red round things Chris?
Kurt
If everything seems under control, you’re just not going fast enough....
Build thread
MKIV complete kit # 9395 delivered 7/31/18
Generation 3 Type 65 Daytona Coupe Complete Kit #151885 received May 6, 2022. Gen 3 Coyote, IRS, Tremec TKX, American Powertrain hydraulic throwout bearing & Wilwood brakes.
MK4 Basic Kit #7404, 347 EFI - Pro M Racing ECM, 30# injectors, 70 mm throttle body, 80 mm MAF, Edelbrock Performer aluminum heads & RPM II intake, all new G-Force T5, 3:55 gears, Pro 5.0 shifter, 3-link, carbon fiber dash/custom Speedhut gauges and paint by Da Bat.
One of my thoughts... but still ?
If everything seems under control, you’re just not going fast enough....
Build thread
MKIV complete kit # 9395 delivered 7/31/18
Generation 3 Type 65 Daytona Coupe Complete Kit #151885 received May 6, 2022. Gen 3 Coyote, IRS, Tremec TKX, American Powertrain hydraulic throwout bearing & Wilwood brakes.
MK4 Basic Kit #7404, 347 EFI - Pro M Racing ECM, 30# injectors, 70 mm throttle body, 80 mm MAF, Edelbrock Performer aluminum heads & RPM II intake, all new G-Force T5, 3:55 gears, Pro 5.0 shifter, 3-link, carbon fiber dash/custom Speedhut gauges and paint by Da Bat.
Generation 3 Type 65 Daytona Coupe Complete Kit #151885 received May 6, 2022. Gen 3 Coyote, IRS, Tremec TKX, American Powertrain hydraulic throwout bearing & Wilwood brakes.
MK4 Basic Kit #7404, 347 EFI - Pro M Racing ECM, 30# injectors, 70 mm throttle body, 80 mm MAF, Edelbrock Performer aluminum heads & RPM II intake, all new G-Force T5, 3:55 gears, Pro 5.0 shifter, 3-link, carbon fiber dash/custom Speedhut gauges and paint by Da Bat.
i do the same thing Chris. Car is getting darn near done and I am driving it but I still look for things to add to the car all the time.
F5R9196 Hand built 347 475hp EFI | T5Z | LSD 3.73 3-link | Power Steering | Power Brakes | Vintage Air | 315/35ZR17 & 275/40ZR17 NT555
HAGERTY. DRIVERS CLUB | Texas Cobra Club
Generation 3 Type 65 Daytona Coupe Complete Kit #151885 received May 6, 2022. Gen 3 Coyote, IRS, Tremec TKX, American Powertrain hydraulic throwout bearing & Wilwood brakes.
MK4 Basic Kit #7404, 347 EFI - Pro M Racing ECM, 30# injectors, 70 mm throttle body, 80 mm MAF, Edelbrock Performer aluminum heads & RPM II intake, all new G-Force T5, 3:55 gears, Pro 5.0 shifter, 3-link, carbon fiber dash/custom Speedhut gauges and paint by Da Bat.
Thanks Chris
(And Bobby lol)
If everything seems under control, you’re just not going fast enough....
Build thread
MKIV complete kit # 9395 delivered 7/31/18
Generation 3 Type 65 Daytona Coupe Complete Kit #151885 received May 6, 2022. Gen 3 Coyote, IRS, Tremec TKX, American Powertrain hydraulic throwout bearing & Wilwood brakes.
MK4 Basic Kit #7404, 347 EFI - Pro M Racing ECM, 30# injectors, 70 mm throttle body, 80 mm MAF, Edelbrock Performer aluminum heads & RPM II intake, all new G-Force T5, 3:55 gears, Pro 5.0 shifter, 3-link, carbon fiber dash/custom Speedhut gauges and paint by Da Bat.
Generation 3 Type 65 Daytona Coupe Complete Kit #151885 received May 6, 2022. Gen 3 Coyote, IRS, Tremec TKX, American Powertrain hydraulic throwout bearing & Wilwood brakes.
MK4 Basic Kit #7404, 347 EFI - Pro M Racing ECM, 30# injectors, 70 mm throttle body, 80 mm MAF, Edelbrock Performer aluminum heads & RPM II intake, all new G-Force T5, 3:55 gears, Pro 5.0 shifter, 3-link, carbon fiber dash/custom Speedhut gauges and paint by Da Bat.
Generation 3 Type 65 Daytona Coupe Complete Kit #151885 received May 6, 2022. Gen 3 Coyote, IRS, Tremec TKX, American Powertrain hydraulic throwout bearing & Wilwood brakes.
MK4 Basic Kit #7404, 347 EFI - Pro M Racing ECM, 30# injectors, 70 mm throttle body, 80 mm MAF, Edelbrock Performer aluminum heads & RPM II intake, all new G-Force T5, 3:55 gears, Pro 5.0 shifter, 3-link, carbon fiber dash/custom Speedhut gauges and paint by Da Bat.