Midwest Classic Insurance

Visit our community sponsor

Thanks Thanks:  0
Likes Likes:  0
Results 1 to 7 of 7

Thread: Braided hose at top of engine?

  1. 08-14-2023, 01:24 PM #1
    FFRWRX
    FFRWRX is offline
    Thinker of thoughts FFRWRX's Avatar
    Join Date
    Feb 2011
    Location
    Bolton, Ontario, Canada
    Posts
    528
    Post Thanks / Like

    Braided hose at top of engine?

    What is this for? Mine is plugged at the end that I'm holding, and then is just visible where the arrow is. From that point it seems to go downwards.

    Screenshot 2023-08-14 at 2.20.24 PM.jpg

    Thank you,

    Rick
    Build page (The Bolton Build): https://thefactoryfiveforum.com/show...ton-Build-818C
    Reply With Quote Reply With Quote
  2. 08-14-2023, 01:35 PM #2
    Ted G
    Ted G is offline
    Ted G's Avatar
    Join Date
    Aug 2021
    Location
    El Dorado Hills, CA
    Posts
    762
    Post Thanks / Like
    My guess would be a vacuum port
    Reply With Quote Reply With Quote
  3. 08-14-2023, 05:13 PM #3
    Hobby Racer
    Hobby Racer is offline
    Senior Member Hobby Racer's Avatar
    Join Date
    Feb 2011
    Location
    Syracuse, NY
    Posts
    1,292
    Post Thanks / Like
    Not a vacuum port. Most likely an oil pressure tap. The original WRX owner most likely has an aftermarket oil gauge installed. With the motor off, unscrew the plug and you should see oil drip out.

    Be sure to put it back before starting the engine.
    MK3.1 Roadster completed 2011
    818R built with EZ36R H6 completed 2018
    818R rebuild with a JDM Honda K24A
    Reply With Quote Reply With Quote
  4. 08-14-2023, 05:54 PM #4
    FFRWRX
    FFRWRX is offline
    Thinker of thoughts FFRWRX's Avatar
    Join Date
    Feb 2011
    Location
    Bolton, Ontario, Canada
    Posts
    528
    Post Thanks / Like
    As long as it is not something stock that I should have connected. I'll try and see when the car is on the lift where it goes.
    Build page (The Bolton Build): https://thefactoryfiveforum.com/show...ton-Build-818C
    Reply With Quote Reply With Quote
  5. 08-14-2023, 07:54 PM #5
    Hobby Racer
    Hobby Racer is offline
    Senior Member Hobby Racer's Avatar
    Join Date
    Feb 2011
    Location
    Syracuse, NY
    Posts
    1,292
    Post Thanks / Like
    That is definitely not stock.
    MK3.1 Roadster completed 2011
    818R built with EZ36R H6 completed 2018
    818R rebuild with a JDM Honda K24A
    Reply With Quote Reply With Quote
  6. 08-15-2023, 06:36 AM #6
    mikeb75
    mikeb75 is offline
    Senior Member mikeb75's Avatar
    Join Date
    Sep 2013
    Posts
    685
    Post Thanks / Like
    Label says "Earls"? It looks like previous owner ran a brake or clutch line to the rear oil galley to tap for oil pressure. Should look like this at the block (minus the sensor):
    18-Install-Accessory-Oil-Galley-Subaru-Adapter__33798.jpg

    The galley plug should be M18-1.5 if you want to blank it off.
    818SC chassis #206 EJ207 2.0L VF37 twin scroll || Cusco type RS 1.5 LSD || Wilwood pedal box (firewall attach) || Wilwood superlite front calipers
    BUILD Phase 1: 6/6/2014 car delivered || 5/24/2015 first start || 6/7/2015 go karted || 4/20/2016 hard-top-topped || 10/25/2016 registered || 11/18/2016 inspected & complete
    BUILD Phase 2: 3/8/2017 EJ207v8 || 5/29/2017 re-first re-start || 7/17/2017 re-assembled with race car bits
    Reply With Quote Reply With Quote
  7. 08-15-2023, 08:50 AM #7
    FFRWRX
    FFRWRX is offline
    Thinker of thoughts FFRWRX's Avatar
    Join Date
    Feb 2011
    Location
    Bolton, Ontario, Canada
    Posts
    528
    Post Thanks / Like
    I'm OK leaving it as-is since it isn't leaking. I can't see where it is going as there are other hoses in the way. The oil pressure tapping makes sense.

    Thanks guy.
    Build page (The Bolton Build): https://thefactoryfiveforum.com/show...ton-Build-818C
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Replica Parts

Visit our community sponsor