Here are some teaser pics of side scoops that i intended sell as soon as i get a set fit and made on my car. Final detail of the mold will still take place.
Visit our community sponsor
Here are some teaser pics of side scoops that i intended sell as soon as i get a set fit and made on my car. Final detail of the mold will still take place.
Im quite happy with how its looking. Needs a few more tweeks. Every time i look at it, i want to change something.
Question: Exposed surface mounted fasteners or hidden?
I want BIGGER!!!!
818S #22 Candy Blue Frame, Front Gas Tank, 2.5L Turbo, Rear radiator, Shortened Transmission, Wookiee Compatible, Console mounted MR2 Shifter, Custom ECU panel, AWIC soon
My Son Michael's Turbo ICE Build X22 http://thefactoryfiveforum.com/showt...rts-818S-Build
My Electric Supercar Build X21 (on hold until winter) http://thefactoryfiveforum.com/showt...e-Build-Thread
Hi I agree with Bob. If they were as wide as the rear wheel fender, another inch or so. Don
.
I vote for hidden fasteners.
What are these scoops going to do ? Where do the they duct to ? Is that the duct behind the car ?
Tony Nadalin
2018 SOVREN Big Bore Champion
2015 SCCA Oregon Region VP3 Champion
2012 ICSCC ITE Class Champion
FFR MkII Challenge Car, Spec Racer, Street Legal, SCCA, ICSCC and NASA Racing
818R Build in progress
Hard to tell since they are black. I was getting ready to make a set out of aluminum. Save me the trouble, but its hard to see but I think they need to be bigger also.
Thanks- Chad
818R-SOLD!!!- Go Karted 7/20/14/ Officially raced NASA ST2- 2/28/15
2016 Elan NP01 Prototype Racecar Chassis #20
1969 Porsche 911ST Vintage Race Car
1972 Porsche 911T (#'s matching undergoing nut & bolt resto in my garage)
Hidden fasteners and a bit bigger for me too. They look good though where there at though.
The ducts will be funneled back to my RMIC via ducting. The duct in the background is 12" and was used to collect the foam dust. Im thinking of using similar duct but black and 6" in diameter to funnel both scoops into the IC.
As they sit now, they are approx 2.5" away from the body. My goal is to make them as large as possible but to not be an eye sore or something that looks out of place.
My goal is to make them adjustable as far as front mouth opening goes and it'd be an easy trim to size desired and install.
Next step after scoops is to make the funnel inside the duct.
Are you planning on making them out of fiber glass to paint match or carbon? Is that 2.5" from the back or the front where the scoop indent is very shallow on the body?
Looks great Kurt, ground breaking as always! I agree with you on as big as possible without being an eye sore. From the angles your showing us, they could easily go bigger without looking out of place. Trim to fit would allow the wide tire guys to go bigger.
Adam _____ Instagram @PopesProjects____ YouTube Channel
818 SRX - #91
Arrived 01/02/2014
First Start 10/31/2016
First Drive 05/22/2017
Registered 10/25/2019 BRAP818
Hows this? About 3.5" opening. I think its perfect.
Hmmm, hard to tell with that along-the-fender view. A side or three-quarter view would help. As it stands, I think I prefer the smaller scoop - more elegant.
And I vote for flush fittings. This isn't some jeep rock-crawler wannabe.
Best,
-j
Looks good Kurt, but we really need more angles of each scoop to give a worthwhile opinion.
Adam _____ Instagram @PopesProjects____ YouTube Channel
818 SRX - #91
Arrived 01/02/2014
First Start 10/31/2016
First Drive 05/22/2017
Registered 10/25/2019 BRAP818
The bigger one looks Great! I like the top angle matching the rear fender angle. How does the contour blend back to the original opening? A nice curve or straight? Top View?? Great work!! Don
Im almost done with the plug. The top angle will mimic the fender lines. Ill post pics tomorrow
Adam _____ Instagram @PopesProjects____ YouTube Channel
818 SRX - #91
Arrived 01/02/2014
First Start 10/31/2016
First Drive 05/22/2017
Registered 10/25/2019 BRAP818
The plug has been built. I should have my final scoops built and installed by next Saturday
Very nice. I love the lines gives it a very aggressive look to the rear section of this car. At least from a side front view.
Looks great kurk! Planning on making them in carbon?
Adam _____ Instagram @PopesProjects____ YouTube Channel
818 SRX - #91
Arrived 01/02/2014
First Start 10/31/2016
First Drive 05/22/2017
Registered 10/25/2019 BRAP818
Or vacuum bag with West System Epoxy. The results would be extremely strong for the clumsy people we know and super light.
Here is a quick vid. https://m.youtube.com/watch?v=LPXn038ahD4
Those look good. I can appreciate the work you put in.
I was hoping for a more rounded top part of the vent more like the rear fender form. But hey, we are all experts right? Beggars cant be choosers
Again, nice work.
Thanks- Chad
818R-SOLD!!!- Go Karted 7/20/14/ Officially raced NASA ST2- 2/28/15
2016 Elan NP01 Prototype Racecar Chassis #20
1969 Porsche 911ST Vintage Race Car
1972 Porsche 911T (#'s matching undergoing nut & bolt resto in my garage)
I'm with Chad. I like where you're going with this, and can appreciate all the work, but I think it would blend in better with all the other rounded surfaces if the top were rounded. Perhaps even pop-up a bit off the fender.
Looks like 200% of what I have with the full open area on my sails.
"Scotty, give me all the TRACTION she's got!" Pictures of what I drive till 818R is finished
Track Car Journal on IWSTI (with build info)
Any thought to developing top scoops to make the intercooler openings on the engine cover larger?
It looks great, it's very similar to the lotus scoops.
Since your so close to the wheel opening it "almost"makes sense to take it to the wheel well like a Porsche 935.
Can we get any tips on the foam you used and techniques?
Adam _____ Instagram @PopesProjects____ YouTube Channel
818 SRX - #91
Arrived 01/02/2014
First Start 10/31/2016
First Drive 05/22/2017
Registered 10/25/2019 BRAP818
Oh that is great!! I love the top angled portion! Aggressive as hell, powwwaaaaaaaaaaa lolll Great stuff Kurk, keep it building!!
Frank
818 chassis #181 powered by a '93 VW VR6 Turbo GT3582R
Go-karted Aug 5, 2016 - Then May 19+21, 2017
Tracked May 27/July 26, 2017
Build time before being driveable on Sep 27, 2019: over 6000h
Build Completed Winter 2021
also this: https://www.youtube.com/watch?v=VodfQcrXpxc
First set came off the mold today. Need to attach the final mounting points for the top and bottom of the front. Ill post more photos once its fully mounted.
Last edited by Kurk818; 04-25-2015 at 07:06 PM.
That looks awesome! Really good work! Very aggressive scoop. Please don't be shy with the pics, we need angles!!!
Adam _____ Instagram @PopesProjects____ YouTube Channel
818 SRX - #91
Arrived 01/02/2014
First Start 10/31/2016
First Drive 05/22/2017
Registered 10/25/2019 BRAP818
I'll buy the first set. I need them before my race.
Thanks- Chad
818R-SOLD!!!- Go Karted 7/20/14/ Officially raced NASA ST2- 2/28/15
2016 Elan NP01 Prototype Racecar Chassis #20
1969 Porsche 911ST Vintage Race Car
1972 Porsche 911T (#'s matching undergoing nut & bolt resto in my garage)