20th Anniversary MK4 Build Thread - #10 of 20 - #8697

[RRussellTx]

Well, I ordered my kit online on Saturday June 18th, 2015 (Best Fathers Day gift ever!) and it was finally delivered by Jim at Stewart around 3:30pm on Friday September 18th just as the kids were getting off the school buses. The kit was completed by FFR on August 22nd so it was within my expectations for the Stewart delivery times based on other experiences I have read on these forums. Now that I have everything here and I have locked in on some key aspects of my build, I thought it was high time I created my Build Thread - so here it goes.


First, a little about the planned build. I really liked the idea of having 427 cubes but I did not think there was enough room for the big block so I locked in on a stroked 351w with a TKO-600 early in the process. I also really liked the idea of having the Ford Racing aluminum block but the incremental cost and the complete lack of practicality left me torn. I also struggled with Carb vs EFI and then what kind of EFI... I struggled with the decision to build the engine myself or have it built by one of the forum vendors. My old man and his crew threatened to pull my 'Man Card' if I let someone else build it so there was no pressure in that decision.

Here is a pic of the crew from the early 70's on one of our weekend motorcycle/camping trips - (I'm the twerp on my great-uncles knee in the red Toughskins).



They were pretty serious gear heads when the Cobra was dominating the race circuits so they are my first line of information and my sounding board for ideas I read on the forums. All that to say that I have struggled on the details of the engine but I have landed in a place that I'm comfortable with. The crew does a lot more talking than working these days so I went with what I consider the 'practical' route and ordered a Forte 427 DART SBF with a Holley Terminator EFI. I think with a 20th Anniversary Mk4 in my garage, my 'Man Card' is safe.

Some of the build plan is still up in the air but I'll update this post whenever I make a decision on something new (or I read it on Edwardb's build log since i'm shamelessly following his lead):

Build List:
20th Anniversary Kit - http://www.factoryfive.com/whats-new...ster-revealed/
Passenger Roll Bars
Wind Wings
Body Cut-outs
Forte DART 427w
Forte TKO-600 with .64 OD
Forte Holley Terminator EFI
Forte Hydraulic Clutch
Forte Seat Heaters
Howe Racing Ball Joints - Edwardb inspired
Moog Tie-Rod ends - Edwardb inspired
Breeze Power Steering Rack

Need to figure out or buy:
Headers
All the bling under the hood
Tires
Paint (final color and whether to do it myself or pay a professional)
Security and maybe electronic start features.
Visors
I'll add to this list as well...

I'll post more details over the next few days until I get caught up.

[BobCarter]

Welcome to the 20th Anniv. Club! I too am a first time builder and have found Edwardp's experience very valuable. If you have some folks with experience near by beleive me they will come in handy. Mounting the center section is a perfect example of having the right tools and the right experience to draw upon. Getting allll the parts is a challenge. Eventually I think they will arrive but it demands working a plan that is flexible. Good luck! Have fun! This will be a memory builder for all of us.

[edwardb]

Congratulations on your kit delivery! I was 95% sure of doing a 427 SBF build with mine before I veered off and went Coyote. Will be very interested to follow your build. The plan sounds great. That DART setup should be excellent. I'm assuming Forte is going to get it completely assembled and dyno'd for you. That takes a lot of drama out of the whole engine thing. Just be patient with the whole process, and enjoy the build. The end result is fantastic. But getting there is too.

[6t8dart]

Welcome to the TX roadster build club! I just started working on mine a month ago. Mine isn't a 20th Aniv edition, but my whole budget was less than that kit cost, so I'm slumming it with a donor build.

[ThickCobra]

Welcome to the 20th A club. I am #4 of 20 and also a first time builder. My family is as excited as I am. As it turns out, I am also going with the Dart 427 from Mike Forte. I know the drama surrounding his new dyno...finally up and running. It sounds like Mike has put up with a lot from the dyno supplier. Your engine may in fact be sitting next to mine. I'm not in a hurry to get it as I am quite a ways from needing it. Tko 600, hydraulic clutch and PS from Forte. I am coming to appreciate the forum. Hard to imagine building the Cobra without support.

Congratulations.

[RRussellTx]

Thanks for the warm welcome. I have spent my spare time in the garage instead of on the computer but I really need to get caught up on this log or I never will.

First, I purchased the differential and knuckles/hubs online from different ebay suppliers right after I bought the kit. I wanted the 3.31 to go with the high torque 427 and TKO-600. I bought the steel differential because FF indicated that it was supported and went with the manual transmission. The ebay seller did not indicate if it was manual or automatic.

The seller shipped the differential with the bolts partially threaded in the aluminum rear cover which damaged the threads during shipping. The seller bought me a new rear cover and took care of the issue. While I was replacing the cover I got to see inside. Here are some pics of the differential:





This is what is behind the vent on the rear cover - it has a small flat cover the attaches with one small screw.

[

I also clean up the knuckles nice and clean like Edwardb - it was not too hard and they turned out pretty nice.




My current problem with the differential is that the driveshaft adapter does not fit properly. The adapter is slightly too large to fit in the indentation of the differential flange. I will follow up with factory five to find out if they have seen this before. My fear is that there are more than one kind of differential flange and they may need different kinds of adapters. They list different kinds in the instructions (clear zinc for automatics and yellow coated zinc for manual) but mine is all black. I'm sure it will get taken care of but worst case I'll be reaching out to Denny's driveshaft to see if they can help.

[RRussellTx]

While waiting for the kit, I ordered several parts and some new toys to help with the build:

Hand rivet gun, pneumatic rivet gun and rivet nut gun:


And my new cleco collection:



I stocked the keezer and the fridge for the 'free labor' I expect to come and help:





And then I got the garage all ready to receive the kit:



After that, I just had to wait for the Stewart truck to arrive with my kit:


He showed up just in time for the girls to help with the unloading process after they got home from school:



And in short order is was tucked away in the garage!

[RRussellTx]

I spent the rest of the evening unpacking boxes and checking packing lists. It looked ok at first but then little things started to look off (like I received 6 springs but only 2 of the 20th anniversary Koni's instead of 4 but I received 2 of the regular front Koni shocks). Nothing was damaged but I could tell I needed to spend a great deal more time going through the inventory process so I shut that down and started the process to get the body off so I could take pictures of everything and check everything out and get that out of the way. I already had the body bucks cutout and the materials on hand but I wanted to get the kit before I set the height on everything. Within a few hours I had the body buck built and the body off:





After that, I spent all day Sunday going through the manual and basically pre-assembling everything to make sure I understood the build and that I have the right parts. I figured out that I don't have the IRS LCA hardware and that I really don't like the IRS differential bushings. They don't seem like they will last very long and I really don't look forward to removing that differential after it is installed. I'll be looking for alternatives there...


I figure it will take a week or two to get through this inventory and get everything tagged and stored with a list of items that I want to replace. Until then, I'm just going to lay low and take it slow so I don't miss something or forget where everything goes. More than one person has said to be patient and I understand why now that the kit is here.

I'll post again when the inventory is complete.

[edwardb]

Great update and progress! Couple comments. The Ford literature specifically states that aluminum center sections are on automatic cars, and cast iron on manual cars. So your center section is from a manual, same as mine. That driveshaft adapter is an expensive part (>$100) so I would expect (demand) FF to resolve it. The one I received, also black, fit my iron case center section perfectly. I just did a little Googling. What Ford has going there is call a Guibo Joint (also sometimes spelled Giubo) which they designed into this setup. It's some kind of rubber donut to take up shock and smooth out the drivetrain. Common on European cars, apparently not as common on U.S. cars. Also see that a 2015 Mustang performance upgrade is to replace this part with a solid adapter and treat it like a traditional pinion flange. So I expect FF is getting them from somewhere. The Driveshaft Shop is one company that talks about this.

I'm surprised about your comments regarding the IRS differential bushings. I have mine completely installed, as I'm sure you saw in my build thread. With the poly bushings, metal sleeves, and everything installed and torqued down, that thing isn't going anywhere. It's extremely rigid. FWIW, I have the Mustang frame for the complete IRS, which has the Ford version of the mountings. They are similar if not slightly less rigid. Granted, one of the performance upgrade in high horsepower Mustangs is to replace those mounts with solids. But that's a much heavier car and way beyond stock power. Personally, I don't think there's anything to worry about.

The pictures of the cover removed from the center section are interesting. Looks similar to the older style 8.8 inside. Would be an interesting side-by-side since supposedly the new one is larger and beefier. The vent tube baffling is also interesting. I haven't seen this addressed in any instructions. Any thoughts about what you're going to do? Mustangs have a pretty long hose that attaches to the nipple and goes who knows where. I'm not sure that's needed here, but seems like it should have something.

One other real minor point. I assume you have your elevated body buck high enough to clear the firewall and dash. But it looks close. Be careful if/when you have the steering wheel installed. It stands higher than the firewall or dash, and it's easy to run into it and (just maybe) scratch it up a bit. One of those "ask me how I know" statements.

[RRussellTx]

Great update and progress!

Thanks!

What Ford has going there is call a Guibo Joint (also sometimes spelled Giubo) which they designed into this setup.

I'm all too familiar with the guibo joint, I put about 200,000 on a 94 325is and replaced this part multiple times' along with other failed suspension parts. I finally put race suspension parts with the urethane bushings and did not need to replace anything until I finally sold it. Granted most of the miles were put on before I swaped the suspension parts but they seemed to withstand the abuse better.

I'm surprised about your comments regarding the IRS differential bushings. I have mine completely installed, as I'm sure you saw in my build thread. With the poly bushings, metal sleeves, and everything installed and torqued down, that thing isn't going anywhere. It's extremely rigid.

It may seem rigid now but I watched too many IRS Mustang YouTube videos about the wheel hop issues they have under full load. With well over 400hp and over 24 inches of rubber on the ground I think it will be much less rigid. I am very concerned about the wheel hop issue primarily because of the amount of effort to rectify it down the road. To your point - it's probably fine but if it's not then we have to pull that bad boy out or live with it until it wears out and then pull it out.

Maybe one of the forum vendors can figure out how to source some solid bushings for us. The guys that are going to put these cars on the track will want them for sure.

The vent tube baffling is also interesting. I haven't seen this addressed in any instructions. Any thoughts about what you're going to do? Mustangs have a pretty long hose that attaches to the nipple and goes who knows where. I'm not sure that's needed here, but seems like it should have something.

I actually have that part in hand. It has a rubber 90 degree tube at the differential end and what appears to be some kind of a filter/one way valve at the other end with hard plastic tubing in between with various mounts and guards along the way. I plan on cutting out the middle and replacing the center with tubing that will allow me to route it somewhere out of the way under the car. It was about a $12 part so it's a cheap experiment.

I assume you have your elevated body buck high enough to clear the firewall and dash. But it looks close. Be careful if/when you have the steering wheel installed. It stands higher than the firewall or dash, and it's easy to run into it and (just maybe) scratch it up a bit. One of those "ask me how I know" statements.

Thanks for the heads up and I'll watch that closely. I have a few inches between the firewall and the body buck but I wanted it high enough to clear the car but low enough to go through the door and its a tight squeeze. I can make up a little room if/when I build the chassis dolly but for now it works fine.

[ThickCobra]

Great update and pics. I'll be looking at the adapter today as I also have the 3.31 center section which is cast iron. I'll also be interested to see whether the vent needs to be addressed. BTW, nice to have a shop dedicated to the build and have to say, luv the keezer.

[ThickCobra]

Great update and pics. I'll be looking at the adapter today as I also have the 3.31 center section which is cast iron. I'll also be interested to see whether the vent needs to be addressed. BTW, nice to have a shop dedicated to the build and have to say, luv the keezer.

[chopthebass]

Couldn't you get your garage floor a little cleaner!

[jayguy]

Awesome setup you have, and looks like it's going to be a great build! Shiner Bock! Great beer! I'm just starting to brew at home, and I think that's going to be a recipe I'll try to find/perfect. It's a great beer.

Glad you guys are blazing the trail with the new IRS. It's still a couple years away (how many years have I been saying that?) but I want to do the '33 with the IRS, and by the time I'm ready, you guys will have ironed out all of the wrinkles. Thanks!


Jay

[ThickCobra]

RRussellTx,

Can I ask how you cleaned up the hubs. Both yours and Edwardb's look fantastic.

[RRussellTx]

ChopTheBass - did I miss a spot?


JayGuy

Awesome setup you have, and looks like it's going to be a great build! Shiner Bock! Great beer! I'm just starting to brew at home, and I think that's going to be a recipe I'll try to find/perfect. It's a great beer.

Thanks! I generally like to have a couple of home brew kegs in the keezer but I just have not made the time lately. I like the Caribou Slobber (medium) and the Big Honkin Stout (dark) extract recipes from Northern Brewer. There is a homebrew store in town where I can pick up the ingredients so I don't actually order from there though.

[RRussellTx]

Can I ask how you cleaned up the hubs. Both yours and Edwardb's look fantastic.

I basically followed Edwardb's instructions. For the knuckles, I used a little file kit from the local big box and a couple of FINE wire brushes for the drill motor. I think Edwardb also used some Emory cloth but his are a little nicer than mine. For the hubs I just cleaned them up with the same wire wheel and put a coat or two of the black POR15. Not hard at all, just took a few hours on a lazy Sunday afternoon.

[BobCarter]

Today I checked the fit off the adapter I received with my kit. I too have a adapter (Black) that does not fit. Its outside diameter is greater than the ID of the center section yoke. To Edwardp's comment- My center section is cast iron, wonder why my black adapter doesn't fit my cast iron center section? Called Vinny at FFR, he's sending me the "right one". Anxious to see what the "right one" will be.


[QUOTE=edwardb;212405]Great update and progress! Couple comments. The Ford literature specifically states that aluminum center sections are on automatic cars, and cast iron on manual cars. So your center section is from a manual, same as mine. That driveshaft adapter is an expensive part (>$100) so I would expect (demand) FF to resolve it. The one I received, also black, fit my iron case center section perfectly. I just did a little Googling. What Ford has going there is call a Guibo Joint (also sometimes spelled Giubo) which they designed into this setup. It's some kind of rubber donut to take up shock and smooth out the drivetrain. Common on European cars, apparently not as common on U.S. cars. Also see that a 2015 Mustang performance upgrade is to replace this part with a solid adapter and treat it like a traditional pinion flange. So I expect FF is getting them from somewhere. The Driveshaft Shop is one company that talks about this.

[CraigS]

RRussel, be sure to stay on FFR about those Konis. When Edward posted about them I did a quick google. WOW, the DA Konis are approximately $950 each.

[ThickCobra]

I basically followed Edwardb's instructions. For the knuckles, I used a little file kit from the local big box and a couple of FINE wire brushes for the drill motor. I think Edwardb also used some Emory cloth but his are a little nicer than mine. For the hubs I just cleaned them up with the same wire wheel and put a coat or two of the black POR15. Not hard at all, just took a few hours on a lazy Sunday afternoon.

Thanks, appreciated.

[ThickCobra]

I have a few questions pertaining to the build, which may be of interest to others.

1. Should there be no rivets drilled thru the main frame members...the large tubes?
2. Should there be no rivets run thru the 11" x 13" plates beneath the ds and ps floor pans? If you do, the rivet will be exposed to the elements. It appears these plates replaced 3/4" cross members.
3. Should the frame be level? I noticed that, although my jack stands were all set on the same notch, and the frame appeared level, it was not. And as we build and torque bolts, etc.,is being level important. I chose to level mine with shims.

Input?

[edwardb]

My input FWIW:

1. I put a row of rivets for the big floor pieces into the main 4 inch chassis tubes. That's the only piece I recall over the main tube. Just make sure to hit the high point down the center so the pieces stay flat. I generally use the FF recommended spacing: Every 3 inches into steel frame members. Every 2 inches for panel-to-panel.

2. Go ahead and put some beads of adhesive on it when installing the panels, but no reason to put rivets into that piece. There are plenty of other frame members around for rivets. That plate is mainly intended for your seat bolts. Also if you use the anti-submarine belt in the center/front of the Simpson harness (you should!) it will bolt into the front of that plate.

3. Doesn't matter. You won't be changing the shape of the frame with the assembly. My garage slopes a bit toward the door (like it's supposed to) and also a bit toward the sides. Nothing to worry about.

[ThickCobra]

Thanks for the quick reply and input. As for item #3, I should have been clearer. My frame sits perpendicular to the main door. That is, sideways. And yes, the floor appropriately slopes toward the main door. There must be some flex to the frame because when I placed a level on the front radiator 3/4" tube is showed one side off level. While a level placed on the back trunk area, in several places, showed it level. Shimming the front leveled everything out and its all good. May not make sense but, thats what I found.

[edwardb]

Thanks for the quick reply and input. As for item #3, I should have been clearer. My frame sits perpendicular to the main door. That is, sideways. And yes, the floor appropriately slopes toward the main door. There must be some flex to the frame because when I placed a level on the front radiator 3/4" tube is showed one side off level. While a level placed on the back trunk area, in several places, showed it level. Shimming the front leveled everything out and its all good. May not make sense but, thats what I found.

I guarantee there is no flex in the frame. Rule that out. But I'm not going to say every part is exactly level to each other. I assume the radiator tube you're talking about is the one just in front of the hood hinges with the two short pieces of 3/4 inch tube the radiator attaches to. Take a look and I'll bet you'll find that part isn't level to the rest of the chassis. Every chassis I've had that piece was welded slightly low on the PS, including my new 20th Anniversary chassis. Just looked. It doesn't hurt anything.

[RRussellTx]

Well, I don't have much of an update but it's been a few weeks since I recorded my build progress so here is the latest.

I went through most of the build manual along with the packing lists and compared them to the parts I received. I pre-assembled as much as I could and that helped me account for everything. The only other item I found missing was the spacers for the front lower ball joint. I was able to pick those up on Amazon and avoid the FFR dependency.

I sent the updated list of what I was missing In addition to the original back order list (rear LCA hardware, 2 Koni's, wrong wheels, bumper hoops) to FFR about a week and a half ago and I was notified after a few days that the request had been submitted to shipping.

I have not received any of the back ordered parts from the initial delivery or the added items that I sent a week and a half ago so I decided to call them today and get an update. He could not give me any firm dates on the key items that I need for the rear suspension but it sounds like it will be at least a month before I get the shocks, sway bars and axles.

Meanwhile, I have finished up the front suspension and power steering rack (except for the back ordered sway bars). I installed the differential which I posted in Edwardb's IRS thread and I have the pedal box and master cylinders initially installed. I say initially because I have a bit of the issue with the clutch arm hitting the chassis. I am not happy about the options that include cutting stuff and I know FFR says it's just fine so I'm trying to convince myself of that or think of another option.

Another issue is that I have the Breeze Power Steering Rack and I also ordered the Offset Rack Mounting Kit but it was harder to line up than the differential was and after looking it over I decided it was not really necessary so I installed it with the delivered bushings. I thought that was just fine until King stopped by this weekend and pointed out the boot rub issue... I spent the rest of the afternoon pulling it out and widening the slotted DS PS Rack mount holes in the chassis so the rack would fit. Now the rack is installed with Mounting Kit and no boot rub.

I have been trying to work on filler work while I wait on the items I need in order to follow the build manual but I really think it's best to stand down for a little while until I get the needed parts and build it more methodically.

Suggestions/ideas on a 3 compartment reservoir are welcome along with words of encouragement to get through the backorder blues!

[RRussellTx]

i also cut the ears off the rear knuckles and ground them down into a more molded look (busy work).



And got some of the bare metal parts Powder Coated:


Here is a shot looking down on the boot rub issue AFTER the fix:


And token shots of the front suspension:

[edwardb]

Sorry to hear you're not making better progress with backorders. I'm down to just the Wilwood brakes, as already mentioned. But it was a full two months after delivery. I called FF and emailed frequently (ask them...) and always received a friendly response. But often without firm promise dates. It's easy to get discouraged. Hang in there! I guess I'm a little surprised about their response to the clutch arm/chassis interference issue. If they don't think it's a problem, then probably why it hasn't been fixed. The interference does exist. No two ways around it. The only way it wouldn't be a problem IMO is if your clutch throw doesn't require the pedal to be pushed down that far (not my experience) or if you raised the pedal up enough to get full release before interference. This would make the clutch higher than the brake, which I also don't like. My suggestion is if you don't want to modify anything at this point, no problem. Wait until you have everything installed, plumbed, etc. and see how it turns out. You should leave the DS footbox outside panels off until the very end of your build anyway, so it would be easy enough to address it later.

Your cleaned up rounded knuckles look great! Looks like they came out of the mold that way. Nice work. I'm surprised you had trouble installing the steering rack and Breeze bushings. Interesting how everyone's experience can be different. It was nothing like installing the IRS center section for me. Now that was hard.

For the triple reservoir, many of us have used the CNC piece. Their part number 1483. I used the double on my first build, and the triple on the last build and will use it again on the new build. In addition to being a nice looking and very functional piece, I really like their pressure cap for bleeding. Check their part number 1459A. Easiest way to bleed the brakes and clutch I've ever found.

For more work, you're stopped about where I was a couple weeks ago. Other things you can work on? Gas tank, radiator, and you could basically complete the instrument panel if you wanted to. You can also start drilling and cleco'ing aluminum panels.

My Coyote engine arrived yesterday. I'll be updating my build thread in the next few days.

[David Hodgkins]

I just wanted to chime in and say I'm following the build and it looks great so far! I do have one question: What kind of rivets are those on your f-panel?

Regarding filler work you have a ton of drilling for all the panels in front of you so that's a good thing to get out of the way and the brake lines are another fun project to tackle. BTW nice work on those Knuckles! Are you going to spray them with a clear or leave them raw? (Oops I guess that's 2 questions...)

[RRussellTx]

I just wanted to chime in and say I'm following the build and it looks great so far! I do have one question: What kind of rivets are those on your f-panel?

Regarding filler work you have a ton of drilling for all the panels in front of you so that's a good thing to get out of the way and the brake lines are another fun project to tackle. BTW nice work on those Knuckles! Are you going to spray them with a clear or leave them raw? (Oops I guess that's 2 questions...)

Thanks! I do my best work when my dad comes in town and helps out. We did most of the knuckles work and the nifty diff install on the same day. I'm going to spray them but not until I fit everything up and make sure I don't have any more filing to do.

The rivets are Allstar White Large Head Rivets - picked them up on Amazon. I like the large head look under the wheel well and on the more structural looking areas. I'll probably go with some much smaller heads when it gets to panel-panel but we'll see.

[ThickCobra]

Great progress. I also have an issue with the ps boots rubbing on both sides. (I purchased the ps unit from Forte Parts who's been great to work with .) At the time I installed it, I merely thought the fit was odd, but thought maybe everything fits a tad tight. I'll need to look at it again tomorrow but not certain as to what I can do.

Also, while centering it, I realized that its 2 1/2+ turns each way. Not certain this is important, but I've read that 3 turns is the norm.

[RRussellTx]

edwardb,

Thanks for the CNC tip and the words of encouragement! I know you feel my pain!
Looking forward to your next update - they always give me some things to do.

[Bhhughes]

Thank you for starting this build thread. I will be watching it with interest because the only thing that may sway me from my planned Coyote based build would be a 427W.

Best of luck with everything!

[ThickCobra]

RRussellTx, this is a general question, but as I suspect many are following your progress, maybe I'm not alone in this issue. I have found an issue relating to properly torquing suspension nut and bolts. I should note that I purchased a new Craftsman torque wrench so I don't believe it's the tool. As you know, several nuts come with deformed ends which make for great lock nuts. However, I am finding that the effort to tighten the nuts often exceeds the torque specs before they are clearly seated. I am finding this often and don't feel comfortable proceeding. In these instances do you merely tighten until they appear seated.

I'm not saying they are difficult to start or to thighten, just that they are tighter than the specs recommend.

Any advise?

[edwardb]

I'll throw my two cents in, and RRussellTx can add his as well. Something doesn't sound right to me. Those big suspension bolts are all mostly 100 ft/lbs torque values. That's a pretty good pull, and if you're nut is stopping at 100 ft/lbs and not seated, maybe something else is wrong. Those deformed nuts do take a little effort, but not that much. Are you sure about the torque wrench? Sure you're on the right range? Do you have another wrench you can use or borrow?

One other comment. My practice is typically to put a dab of anti-seize on all the suspension bolts before assembly. I find it's just good practice for the future if/when having to take them back off. I also put it on all stainless hardware, regardless of size, but that's to prevent galling and seizing which stainless is famous for. I don't think that's what's happening here. But it does provide a little lube to the threads. If you are stopping before being seating, i wouldn't expect that to fix it though.

[ThickCobra]

Thanks for the feedback. Problem identified and do I feel foolish, yet glad I asked. Operator error!!! Here's a hint as to what my problem was. A 250 inch lb. wrentch is not the same as a 150 ft lb wrench. Next time I wear my reading glasses. Tomorrow morning I redo all bolts.

[RRussellTx]

Well, it's past time for some updates so here is the latest. I've received most of my backordered parts except for the brakes and the CV axles so I was able to make some progress on the front end and a few other areas.

First up is the radiator. I purchased the Breeze Aluminum Fan Shroud #32088, The Hinged Mounting Kit #70558 and the Lower Radiator Support Kit #70551. I cut off the original mounting tabs, touched up the paint with the Rustoleum recommended by Edwardb and then centered the hinged mounting kit.





I also cutout the fan shroud and got it prepped for powder coating. I'm still undecided on what color to powder coat everything but I am now leaning towards white for everything.

[RRussellTx]

I also prepped the gas tank and fuel filters when my dad was in town. We straightened out the tabs on the side of the fuel tank but the paint cracked when we straightened it so I prepped the edges and touched it up with POR15. I also added the 255 lph in-tank fuel pump for the Holley Terminator EFI as well as the Holley Fuel filters. We also fabbed up a mounting bracket for Fuel Filters since they don't really fit anywhere on the chassis. I'll get that powder coated next week along with some other parts like the sway bar mounting brackets that were not on my original order.



This is the fuel filter mounting plate in place under the trunk area:


This is the same plate with the fuel filters placed in the approximate location as they will hang under the plate. I should be able to connect this to the fuel tank with a short 6AN flexible hose.

[RRussellTx]

I also drilled and cleco'ed some of the foot box panels:


And finished up the front end by mounting the sway bars. The spacers put the rod ends at a pretty good angle even after we trimmed them to the 1/2 inch. We wound up trimming the spacers by about 3/8 of an inch to get the rod ends to hang correctly. This picture does not show it well but it does show the completed front suspension which is worth recording!

[RRussellTx]

I have a few more things that I can work on but I really want the rear end parts and the engine so I can move forward with the big stuff first to help me visualize a few more things. Forte is running into more delays on the motor and I can't get a firm update from FF on the axles yet. No worries though, the excitement of getting started has subsided and I'm just enjoying the process. I realize that patience is the most critical ingredient for the build. Every time I get in a hurry, something gets a little off and everytime I really take my time it comes out great. I also have work and family time to balance so I'm starting to get in a groove there too. (I have been interrupted several times while getting this update written).

I'll update again after Thanksgiving when I should get a few days off to work on the car - a few of them with dad in town.

[edwardb]

Looking good. And familiar. I hadn't seen the Breeze upper radiator mount quite that clearly before. Interesting. I wasn't sure about the white powder coat, but the more I see it the more it's growing on me. You're doing some nice work there. I assume you know that retainer ring on the gas tank filler will have to be removed and then replaced when you put in the filler tube. There's a bead on the filler tube that goes inside the retainer.