Dmac800 father/son build

[Dmac800]

My 17 year old son and I will be building the Type '65. We are excited to do this project together and can't wait for it to get here.

I ordered the kit on 7/8/24 with a completion date of 10/05/24. Then we have to wait for Stewart transport to get it to Puyallup, WA. so maybe we will have it by the end of October or early November.

The build:
Complete Kit
Gen3 Coyote
T56 Trans
IRS
Heat and AC
power steering
Front and rear sway bars
Carpet
18" Halibrands

removed seats, side pipes, and exhaust

Thinking of adding door sills and indoor cover

Don

[460.465USMC]

Congrats, Don! You are in for a lot of fun. So glad you were able to start the project while your son is still home. Thanks for starting a build thread. Looking forward to it. Subscribed.

[Jphoenix]

Hey Don, ours will be here in about 3 weeks, so you’re welcome to come up the hill and check it out!

[Dmac800]

I have received my Gen3 Coyote and the control pack. In the control pack there are two sensors in a bag that look like they are the EGT sensors. They look used. Is this normal? I hope the picture posts.


Attachment 203155

[Dmac800]

Thanks JohnK for the response on the O2 sensors.

[Dmac800]

I am going to put Por15 on the Diff, and was wondering how everyone applies it. Do you use the spray cans, paint brush, or HVLP paint gun?

[gbranham]

I've always used a paint brush. The only thing that gets it off of skin is time, so glove up well!!

Greg

[460.465USMC]

Hi Don. I also have only used a brush. I liked the application best with a foam brush. I think you'll really like the results.

[Dmac800]

My kit should be close to being finished by FFR and I was wondering if they automatically will send me pictures or if I have to ask for them? My kit was to be completed on 10/5/24 but Stewart Transport asked to have it moved up so that they can put it on the same truck that they already have going to Washington tomorrow.

[460.465USMC]

I've had to call them on both builds to get a "nursery" picture. They've always been happy to accommodate me, and I have no doubt they will do the same for you, if you reach out.

[Dmac800]

I will call tomorrow morning and see if it is not to late. Hopefully they were able to accommodate Stewart Transport and got my coupe done early. Stewart has my ETA of 10/13/24.

[460.465USMC]

Wahoo! Getting close now. Christmas in October!

[Dmac800]

I just got off the phone with FFR and they said that my kit will be loaded on the truck today!!!!!!! Can't wait to start building with my son.

[PNWTim]

You're about 2 1/2 months ahead of me. Good luck on your build kick off!

[JimStone]

I asked for but never got the "nursery" picture.

So this was my first glimpse of the car, which made it even more exciting

[Dmac800]

I am debating on upgrading my shocks to QA1 DD401's because I hope to do track days and the Silver State Classic some day. Where is a good place to get them from?

[Dmac800]

I am working on our Coyote and was wondering if anyone knows what the torque spec is for the oil filter nipple? I removed the oil cooler and want to get the filter put back on the engine. I don't want to over tighten it and cause any damage. I also dropped the oil filter and it has a small dent in the side. Should I replace it?

[Dmac800]

Our coupe was delivered yesterday afternoon!!!! Now we get to start the inventory process.

[Jphoenix]

I am debating on upgrading my shocks to QA1 DD401's because I hope to do track days and the Silver State Classic some day. Where is a good place to get them from?

I bought mine from Summit.

[Dmac800]

I bought mine from Summit.

When you get them from Summit, do they come with the springs? What spring rate?

[Dmac800]

20241013_131403.jpg20241013_131704.jpg Here are a couple of pictures of the Coupe set up in my garage.

[Jphoenix]

When you get them from Summit, do they come with the springs? What spring rate?

No springs, just the shocks. For now I'm using the springs that came from FFR - 750/500 I think? I'll replace them with 900/700 springs ( or thereabouts) for racing.


The DD401 shocks come with different ID bushings, you can remove the bushings from the FFR shocks and use them in the QA1 shocks by removing the circlip, saves having to fabricate new bushings for the QA1's.

[Dmac800]

Thanks

[slarson]

I am debating on upgrading my shocks to QA1 DD401's because I hope to do track days and the Silver State Classic some day. Where is a good place to get them from?

I got mine from Gordon Levy. He spent at least 30 minutes on the phone asking what my plans were for the car so he could determine the proper spring rates for my application.

Congrats on the delivery, now the fun really begins. Enjoy the build with your son, these times are precious! I bought my kit with the same intention but my son moved to Colorado before mine was delivered. He's coming home this weekend for a few weeks and the plan is to achieve the engine first start.

[PNWTim]

Congratulations on having it in house! I am still two months away so living vicariously through the various build threads in the forum, including yours. Enjoy!

[Dmac800]

I want to put a Tire pressure system in my 18" Halibrands. I purchased the Schrader 33700 Clamp-in Programmable EZ-Sensor's but they won't work. Has anyone found a sensor that will work?

[460.465USMC]

Hi Don. Hope you're having a good time with your son on the build so far.

Not long ago another forum builder, Rsnake, posted a video about his TPMS Schrader system: https://youtu.be/_sSwKCSQiiQ?si=XDJ8FrnEO4edmBnp. Hope this helps.

[Dmac800]

Hi Don. Hope you're having a good time with your son on the build so far.

Not long ago another forum builder, Rsnake, posted a video about his TPMS Schrader system: https://youtu.be/_sSwKCSQiiQ?si=XDJ8FrnEO4edmBnp. Hope this helps.

Hi Chris. We have been busy with getting the inventory done and finally finished it Saturday night.

I have watched all of Rsnake's videos and purchased those Schrader sensors and unfortunately, they don't work with the Halibrands.