-
Senior Member
My axle contacts the panhard frame mount
I’m a bit confused. My frame had a gap like shown. I drilled like the instructions say but when you tighten it it pulls it in. Then it contacts the axle. The picture show the gap now. One example I tighten it up it pulls it in then contact is made. I have the shocks mounted in the lower hole on the upper mount.
I can use some advice
DFF90955-5E43-4AF6-A408-13748A5C4C1E.jpg. 3E333DD8-0478-4DDB-8F3A-BB65583B8CBB.jpeg ACF135B1-8D54-400B-ADE9-CBA8AE3535C0.jpg
MK4 #10008 - Ordered 10/06/20, Delivered 03/03/21, First Start 7/22/21, First Go Kart 7/24/21
Paint by Metal Morphous 5/14/22, Legally registered 6/8/22, Graduated 7/20/22
Build Thread
https://thefactoryfiveforum.com/show...been-delivered
Complete Kit, Ford 306, Sniper/Dual Sync, T5, Hydraulic clutch
-
Senior Member
Oh man, I had my upper link too tight. I apparently just needed to freak out on the forum to see it
MK4 #10008 - Ordered 10/06/20, Delivered 03/03/21, First Start 7/22/21, First Go Kart 7/24/21
Paint by Metal Morphous 5/14/22, Legally registered 6/8/22, Graduated 7/20/22
Build Thread
https://thefactoryfiveforum.com/show...been-delivered
Complete Kit, Ford 306, Sniper/Dual Sync, T5, Hydraulic clutch
-
Post Thanks / Like - 0 Thanks, 1 Likes
-
Not a waxer
If you have the axle hanging at full droop it will contact the panhard mount tube that runs forward to the round tube.
Jeff
-
Post Thanks / Like - 1 Thanks, 0 Likes
-
Senior Member
Originally Posted by
Jeff Kleiner
If you have the axle hanging at full droop it will contact the panhard mount tube that runs forward to the round tube.
Jeff
I’m so relieved, Thanks Jeff. I took it apart twice. Since I have your attention what are these for? I went over the manual 10 times, they are my only leftovers from the 3 link HW kit. I had a longer one for the upper bracket brace, but I can’t find a home for these.
9862070F-497C-463F-AEF9-FE213946774B.jpg
MK4 #10008 - Ordered 10/06/20, Delivered 03/03/21, First Start 7/22/21, First Go Kart 7/24/21
Paint by Metal Morphous 5/14/22, Legally registered 6/8/22, Graduated 7/20/22
Build Thread
https://thefactoryfiveforum.com/show...been-delivered
Complete Kit, Ford 306, Sniper/Dual Sync, T5, Hydraulic clutch
-
I had those left over too.
Ordered 9/24/2020, Delivered 1/18/2021 MK4 Roadster, 3 Link, 15" Halibrands, Blueprint Carb 347/TKX Installed 3/13/2022, first start 10/2022, go cart 11/2022, CA SB100 Reg Complete 12/2023
-
Post Thanks / Like - 1 Thanks, 0 Likes
-
Senior Member
Originally Posted by
Daddy O
I had those left over too.
Outstanding
MK4 #10008 - Ordered 10/06/20, Delivered 03/03/21, First Start 7/22/21, First Go Kart 7/24/21
Paint by Metal Morphous 5/14/22, Legally registered 6/8/22, Graduated 7/20/22
Build Thread
https://thefactoryfiveforum.com/show...been-delivered
Complete Kit, Ford 306, Sniper/Dual Sync, T5, Hydraulic clutch
-
Senior Member
Yes, at full drop the axle rests on the mount. Mine does it too. You can see we have a rag between the axle and the mount where it makes contact.
I also had those two bolts left over. I ended up using them to mount the pedal box to the front of the foot box because I was missing those bolts and they are the exact same bolt!
20210216_233011.jpg