-
Two and half years in
E2A8BCC1-1A20-402F-B9A8-EE6902A41334.jpeg
A bit of a milestone, body on, for what I hope is the last time. Heads up for those who install heater / defrost! Defroster vents “must be closer to the center “! Gonna have to fabricate a plenum on the passenger side. The warning may have been in the instructions...either way the vent outlet cannot be above the heater box! Other than that, here’s about 2.5 yrs of work...but it’s been fun!
MK IV complete Kit - 1st time builder started Sept 2016
Levy 306
T5
2015 Mustang IRS
Power steering - Levy setup, Breeze roll bars, Thompson trunk box
fuel injection, powder coating, sway bars, heater, wipers, 17 in wheels
-
Post Thanks / Like - 0 Thanks, 2 Likes
-
Fantastic Job! Keep it up!
Dave
Mk 3.1 - #6882 - 5.0L 302 - FiTech EFI - 3-Link - 3.08 Ratio - 15" Wheels
Greenhorn and doing the best I can
My photos are at:
My Flickr acct
Videos are at:
YouTube Videos
-
-
MKIV complete kit w/powder coating and cut outs, serial #9189 delivered 10/10/17, first start - 10/5/18, legal - 10/08/20. Blueprint 306 w/Holley Sniper EFI, TKO 600, power steering, Breeze fan shroud, trunk cubby, & engine compartment battery kit, CNC brake reservoirs, RT turn signal & gas pedal, mechanical throttle linkage, METCO safety loop, GASN side pipes, drop trunk, dual chrome roll bars, vintage gauges, glove box, custom center console, cup holders, and speakers.
-
Senior Member
Very nice! I like the white and blue or are they black stripes?
Kyle
Complete Kit pickup 09/05/2015, 351w, QF680, 3.55, 3-Link, 15" Halibrands with MT's, Painted Viking blue with Wimbledon white stripes on 03/15/2017. Sold in 08/2018 and totally regret it.
-
Greetings. I have been looking at a lot of whites for my coupe and nothing stands out but I do like yours. Would you be willing to share the color and paint code. Any photos outside? Thanks and good looking car. Thansk
-
Senior Member
Looking great. Re; defroster. I've had an APE hardtop for 10 yrs and it stays on the car year around. I've gotten caught in the rain quite a few times but needed a defroster maybe 5 times. If that plenum gets to be too difficult, I'd just forget the defroster. Cap the outlets and you will get more from the heat outlets. Keep a towel in the car.
FFR MkII, 408W, Tremec TKO 500, 2015 IRS, DA QA1s, Forte front bar, APE hardtop.
-
Post Thanks / Like - 1 Thanks, 0 Likes
WIS89 thanked for this post
-
Senior Member
CVOBill
MK2 #???? Delivered 11/2002, Finished and Titled 6/2003 5.0, T-5, 4-Link, Sold 3/2005
Hot Rod #304 purchased 5/28/2017 from original owner Unassembled . Titled and plated 8/24/2017 Coyote,
TKO, 3-Link, Heat, A/C, Electric Power Steering, Convertible top
MK4 #9524 Picked up 1/18/19 306 Blueprint, T-5, 4-Link, Gas-N Pipes, Heater
-
Senior Member
looks great. congrats on the build milestone!
MK4 #8900 - complete kit - Coyote, TKO600, IRS - Delivered 6/28/16 First Start 10/6/16 Go cart - 10/16/16 Build completed - 4/26/17 - 302 days to build my 302 CI Coyote Cobra - Registered and street legal 5/17/17
Build Thread
http://thefactoryfiveforum.com/showt...e-build-thread
PHIL 4:13 INSTAGRAM - @scottsrides
-
Post Thanks / Like - 1 Thanks, 0 Likes
Jacob thanked for this post
-
Not a waxer
Looking good Jacob!
Heater box and defroster boot don't play well together on the passenger side. I cut and reglassed a full width plenum one time but it still didn't work really well on the RH side. Now any heat and defrost cars I do get a functional defroster vent in front of the driver and a non-functional dummy grill on the passenger side.
Jeff
-
Post Thanks / Like - 2 Thanks, 1 Likes
-
check out North Race Cars, Richard Oben, he has a plenum for just this issue, I just got mine and not installed yet but in test fitting it is going to work fantastic. It will allow you to put your vents anywhere you want.
-
Post Thanks / Like - 0 Thanks, 1 Likes
-
Last edited by Jacob; 02-08-2019 at 12:51 PM.
MK IV complete Kit - 1st time builder started Sept 2016
Levy 306
T5
2015 Mustang IRS
Power steering - Levy setup, Breeze roll bars, Thompson trunk box
fuel injection, powder coating, sway bars, heater, wipers, 17 in wheels
-
Originally Posted by
ricobrafan
Greetings. I have been looking at a lot of whites for my coupe and nothing stands out but I do like yours. Would you be willing to share the color and paint code. Any photos outside? Thanks and good looking car. Thansk
Sure, pics included, if you can’t pull up the details on the paint, let me know. The colors chosen were the result of 2 yrs oh agonizing over “go original or new paint “? Finally decided it needs to be original for the most part but I cheated on the blue, it was a compromise, not old put would agree with the W white.
C8767035-CECE-4A56-925E-45A87AB0235E.jpeg
85BEC8E3-B953-4CB9-9AAC-ACE95770BBFB.jpeg
00C777FF-F82B-49A3-9E8B-4696E1373A88.jpeg
95CD7B0A-2E02-4D60-AEDD-688A0876CAE3.jpeg
MK IV complete Kit - 1st time builder started Sept 2016
Levy 306
T5
2015 Mustang IRS
Power steering - Levy setup, Breeze roll bars, Thompson trunk box
fuel injection, powder coating, sway bars, heater, wipers, 17 in wheels
-
Originally Posted by
Jeff Kleiner
Looking good Jacob!
Heater box and defroster boot don't play well together on the passenger side. I cut and reglassed a full width plenum one time but it still didn't work really well on the RH side. Now any heat and defrost cars I do get a functional defroster vent in front of the driver and a non-functional dummy grill on the passenger side.
Jeff
Not real concerned about the passenger and really don’t expect to use the defrost, but I’ll try to make a plenum, if it works ok, if not I’ll plug it off. Thinking 1” thick, 9” wide, 4” deep?
MK IV complete Kit - 1st time builder started Sept 2016
Levy 306
T5
2015 Mustang IRS
Power steering - Levy setup, Breeze roll bars, Thompson trunk box
fuel injection, powder coating, sway bars, heater, wipers, 17 in wheels
-
Senior Member
That's a great looking white car!
Started dreaming of a Cobra around 1987
Purchased Complete Kit 6/9/2017, Delivered 9/4/2017, Rolling Chassis 3/30/2018, Engine Dyno'ed 3/4/2022, Engine installed 8/27/2022
Click here for my build thread
Serial #9158
Design Engineer at BluePrint Engines
-
Post Thanks / Like - 1 Thanks, 0 Likes
Jacob thanked for this post
-
Not a waxer
Originally Posted by
SDhemmings
check out North Race Cars, Richard Oben, he has a plenum for just this issue, I just got mine and not installed yet but in test fitting it is going to work fantastic. It will allow you to put your vents anywhere you want.
That's the one I had to cut up to work (sort of) on a Mk4.
Jeff
-
Thanks for the info and the additional pictures.
-
Post Thanks / Like - 0 Thanks, 1 Likes
-
Jacob-
Those new pictures do a great job showing off that beautiful paint! I liked the picture of the body on that you posted the other day. However, those extra ones you posted really show off that great looking paint job. She looks great, and I know you must feel terrific after getting to that milestone.
Please show some more pictures after you get her all put together. Congratulations again!
Regards,
Steve
-
Post Thanks / Like - 0 Thanks, 1 Likes
-
Senior Member
Mk4 #9165, Base Kit with lots of options, Delivery on 08/17/2017, Coyote, TKO600, 2015 IRS, 18" Halibrands, 12.99" Wilwoods